manualshive.com logo in svg

Ricoh A763, Manual

Share
Download
Ricoh A763 Manual Download Page 57

ADJUSTMENT 

30 August, 2002 

A763-56 

 

 

Dip switch 1 -6, -7, -8 setting 

-6 -7  -8 

Adjustment  

(0.25 mm/ step) 

OFF ON  ON 

+3 

OFF ON  OFF 

+2 

OFF OFF  ON 

+1 

OFF OFF  OFF 

0 

ON OFF  ON 

-1 

ON ON OFF 

-2 

ON ON  ON 

-3 

ON 

OFF 

OFF 

Do not use 

 

8.  Measure the distance (L) between the stapling position and the folder position. 

9.  Adjust the stapling position with dip switches 1 -6, -7, -8. 

Inputting a lower value than the current setting moves the stapling position 
towards the leading edge. Adjusting by 1 step moves the stapling position 0.25 
mm. 
 

Example 1:

 

To move the stapling position 1 mm towards the leading edge. 
If dip switch 1 is currently set to +2, set the dip switch to reflect -2 (this moves 
the stapling position 4 steps towards the leading edge). 

Example 2:

  

To move the stapling position 0.75 mm away from the leading edge. 
If dip switch 1 is currently set to -1, set the dip switch to r2 (this move,s 
the stapling position 3 steps away from the leading edge).  

10. Turn off dip switched 1-1 and -2, then turn off the copier main switch. 

Mark

Example 1: L= 1 mm

Adjust towards the leading edge

L

Mark

Example 2: L= 0.75 mm

Adjust away from the leading edge

L

Stapling Position

Folding Position

Folding Position

Stapling Position

A763R559.WMF

Summary of Contents for A763





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands