Ricoh A763 Manual Download

Page: 7 / 60

ELECTRICAL COMPONENT DESCRIPTION

30 August, 2002

A763-6

Symbol Name

Function

Index

No.

Solenoids

SOL1

Booklet Gate

Drives the booklet gate.

SOL2

Buffer Roller
Entrance Gate

Drives the buffer roller entrance gate.

SOL3

Proof Tray Gate

Drives the proof tray gate.

SOL4

Buffer Roller
Exit Gate

Drives the buffer roller exit gate.

SOL5

Transport Belt

Moves the transport belt to the stopper.

SOL6

Paddle

Releases the paddle stopper.

SOL7

Front Guide
Release

Releases the front guide plate.

SOL8

1st Booklet Unit
Gate

Drives the 1st booklet unit gate.

SOL3

2nd Booklet Unit
Gate

Drives the 2nd booklet unit gate.

SOL4

Relay Roller

Releases the relay roller.

PCBs

PCB1

Finisher

Controls the upper unit.

PCB2

Lift Motor
Sensor

Generates pulses to check the lift
motor, to control lift motor position, and
to detect the motion direction of the
shift tray.

PCB3

Booklet Unit

Controls the booklet unit.

PCB4

Trailing Edge
Sensor

Detects the relay roller release timing.

Others

HR1

Stapler Interface Interfaces the stapler and the finisher

board.

Summary of Contents for A763





























































Search results

Summary of Contents for A763

Reviews:

Related manuals for A763

Brands by name

Popular brands

Ricoh A763, Manual

Search results

Summary of Contents for A763

Reviews:

Related manuals for A763

Brands by name

Popular brands