Ricoh A763 Page 55 Manual Download

Page: 55 / 60

ADJUSTMENT

30 August, 2002

A763-54

4.2.4 BOOKLET STAPLING POSITION

After replacing the booklet board, dip switches 1 -6, -7, -8 on the new board must
be set up the same way as on the old board.

1. Remove the lower right cover (see “Booklet Unit Removal”) and lower rear

cover.

2. Turn on dip switches 1 -1 and -2 on the booklet board.

3. Tape the actuators of the booklet entrance guide sensor (S42) and the booklet

entrance guide safety switch (SW11), so that S42 and SW11 remain actuated.

4. Press switch 2 (SW2) on the booklet board.

•

After pressing the switch, the booklet transport motor (M10) will start to
rotate.

5. Put a mark on the trailing edge of some A3/11" x 17" paper (two sheets).

SW2

Dip Switch 1

LED 1

A763R557.WMF

Dip Switch 1

A763R556.WMF

Mark

(Trailing edge)

Slot in direction
(reading edge)

A763R558.WMF

Summary of Contents for A763





























































Search results

Summary of Contents for A763

Reviews:

Related manuals for A763

Brands by name

Popular brands

Ricoh A763, Manual

Search results

Summary of Contents for A763

Reviews:

Related manuals for A763

Brands by name

Popular brands