Ricoh A763 Manual Download

Page: 52 / 60

30 August, 2002

ADJUSTMENT

A763-51

Options

4.2 ADJUSTMENT

4.2.1 SHIFT TRAY HEIGHT

After replacing the finisher board or shift tray height sensor, always do this
adjustment.

1. Remove the upper rear cover.

2. Turn on dip switches 3 -1 and -4 on the finisher board.

3. Put blank paper (A4/8

1/2

11") on the shift tray.

4. Press switch 1 (SW1) on the finisher board.

The finisher automatically adjusts the shift tray height when switch 1 is pressed.

•

After performing the adjustment, the shift tray will return to home position.

•

During the adjustment, LED 1 flashes. After performing the adjustment, LED
1 turns on and remains on.

•

If the automatic adjustment fails, the finisher stops and LED 1 turns off.

5. Turn off dip switches 3 -1 and -4, then turn off the copier main switch.

SW1

SW2

Dip Switch 3

LED 2

LED 1

A763R550.WMF

Dip Switch 3

A763R551.WMF

Summary of Contents for A763





























































Search results

Summary of Contents for A763

Reviews:

Related manuals for A763

Brands by name

Popular brands

Ricoh A763, Manual

Search results

Summary of Contents for A763

Reviews:

Related manuals for A763

Brands by name

Popular brands