Ricoh A763 Manual Download Page 53

Page: 53 / 60

ADJUSTMENT

30 August, 2002

A763-52

4.2.2 JOGGER FENCE POSITION

After replacing the finisher board or if a paper alignment fault occurs, do this
adjustment.

Doing this adjustment once will affect all paper sizes.

1. Remove the upper rear cover.

2. Turn on dip switch 3-1 on the finisher board.

3. Press the following switch on the finisher board.

Using A4: Switch 1 (SW1)
Using 8

1/2

" x 11": Switch 2 (SW2)

•

After pressing the switch, the upper exit unit will open and the jogger fences
will move to the A4 or 8

1/2

" x 11" position.

4. Place 10 sheets of A4/8

1/2

" x 11" paper between the jogger fences and push

them until they touch the shutters.

5. Adjust the jogger fence position by pressing switch 1 or 2.

•

Switch 1: Move to the front (0.35 mm/press)

•

Switch 2: Move to the rear (0.35 mm/press)

6. Press switches 1 and 2 simultaneously to store the adjustment data.

•

After pressing the switches, the upper exit unit will close.

7. Turn off dip switch 3-1, then turn off the copier main switch.

SW1

SW2

Dip Switch 3

LED 2

LED 1

A763R550.WMF

Rear

Jogger Fence

Front

SW2

SW1

Shutter

A763R553.WMF

Dip Switch 3

A763R552.WMF

Summary of Contents for A763





























































Search results

Summary of Contents for A763

Reviews:

Brands by name

Popular brands

Ricoh A763, Manual

Search results

Summary of Contents for A763

Reviews:

Brands by name

Popular brands