manualshive.com logo in svg

Ricoh A095, Service Manual

Share
Download
Ricoh A095 Service Manual Download Page 590

BULLETIN NUMBER:      6645/6655/6665-034

02/17/95

APPLICABLE MODEL: FT6645/6655/6665

SUBJECT: SOFTWARE MODIFICATION

GENERAL:

The Main Control Board ROMs (A0965151 and A0965153) have been upgraded to version "B".

CAUTION:

Whenever upgrading the old Main Control Board ROMs to the new version ROMs in the
field, you MUST also perform the mechanical modification described on page 3 (see
UPDATE NO. 7 -  BUILT-IN LCT LIFT MOTOR CONTROL MODIFICATION).  Replacing the
ROMs without performing this modification might lock the built-in LCT so that it cannot
open. This is because the bottom plate stops at a slightly higher position due to the
motor’s quicker response.

The modifications to the new software are as follows:

••

UPDATE NO. 1 -

MACHINE ENTERS THE SCREEN SAVER MODE DURING AUTO COUNTING

If the machine enters the Screen Saver Mode while performing original Auto
Count, after counting all the originals, the machine indicates an original misfeed.

Countermeasure -

The machine does not enter the Screen Saver Mode while Auto Counting
originals.

••

UPDATE NO. 2 -  

OPERATING TIME INDICATION IS INCORRECT  

 

During normal operation, the time remaining before the end of the copy job is
indicated by animation on the touch panel screen. However, during duplex mode
when using the RDH and Finisher, the indicated time was incorrect.

Countermeasure - 

For Single Side Original to Duplex Copy Mode, it is impossible to calculate the
time due to the complex operation using the alternate feed system.  Therefore, in
this mode, the operating time is not indicated.

For Duplex Original to Duplex Copy Mode, the accuracy of the indicated operation
time has been improved.

••

UPDATE NO. 3 - 

THE RDH/FINISHER MAXIMUM COPY SET LIMITATION IS 50 SETS

  

If a number larger than 50 was entered, it was canceled and "50" was displayed.

Countermeasure - 

When using the RDH and Finisher, the selectable copy set for sort mode has
been changed to "999" (In the sort mode, due to the alternate feed operation, the
paper stacked in the duplex tray is always less than 50 sheets). 

Continued...

Summary of Contents for A095









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands