manualshive.com logo in svg

Ricoh A095, Service Manual

Share
Download
Ricoh A095 Service Manual Download Page 359

     

4) Lock the adjusting (upper) dials [A] by fully rotating the lock (lower)

dials [B] clockwise.

NOTE: Height should be proper when the gap [C] is 2 mm. If the height

adjustment is not completed even if the gap [C] is less than 3
mm, remove the cover [D] (4 screws), and loosen then tighten 4
screws [E]. Then adjust the height again.

 9. Plug in the copier and turn on the main switch.

NOTE: The copier automatically recognizes that the DJF has been

installed.

10. Make copies using the DJF and confirm the copy image.

Rev. 4/15/94

[B]

[A]

[C]

[D]

[E]

A095/A096/A097

7-10

FSM

Summary of Contents for A095









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands