manualshive.com logo in svg

Ricoh A095, Service Manual

Share
Download
Ricoh A095 Service Manual Download Page 308

1.4

LENS MAGNIFICATION

SC140 - Lens vertical home position sensor abnormal - stays off (Stays
OV).

Definition: [level: D]
When the lens returns to the home position, the lens vertical home position
sensor does not detect the on condition (5V) for 2 seconds or more, and
more than twice.

Possible causes:

•

Lens vertical home position sensor shorted

•

Lens vertical drive motor defective

•

Optics control board defective

SC141 - Lens vertical home position sensor abnormal - stays on (Stays
5V).

Definition: [level: D]
When the lens returns to the home position, the lens vertical home position
sensor does not detect the off condition for 3.5 seconds or more, and more
than twice.

Possible causes:

•

Lens vertical home position sensor open

•

Lens vertical drive motor defective

•

Optics control board defective

SC142 - Lens horizontal home position sensor abnormal - stays off
(Stays OV).

Definition: [level: D]
When the lens returns to the home position, the lens horizontal home position
sensor does not detect the on condition (5V) for 1.7 seconds or more, and
more than twice.

Possible causes:

•

Lens horizontal home position sensor short

•

Lens horizontal drive motor defective

•

Optics control board defective

T

rou

bl

e

-

sh

o

o

ti

n

g

FSM

6-5

A095/A096/A097

Summary of Contents for A095









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands