Ricoh A095 Service Manual Download Page 42

Page: 42 / 680

4. ELECTRICAL COMPONENT DESCRIPTION

Refer to the electrical component layout on the reverse side of the attached
Point to Point for symbols and index numbers.

Note: For RT31 descriptions, see Section 7, page 3.

Symbol

Name

Function

Index

No.

Motors

M 1

Scanner Drive

Drives the 1st and 2nd scanners
(dc servo).

M 2

Exhaust Fan

Removes the heat from around
the fusing unit.

M 3

Main

Drives the main unit components.

M 4

Development Drive

Drives the development unit.

M 5

By-pass Feed

Drives the by-pass feed rollers.

M 6

3rd Scanner Drive

Drives the 3rd scanner (dc
stepper)

M 7

Toner Bottle Drive

Rotates the toner bottle to supply
toner to the toner hopper.

M 8

Charge Wire
Cleaner Drive

Drives the main charge wire
cleaner to clean the charge wire.

M 9

Jogger

Drives the jogger fences to
square the paper stack in the
duplex tray (dc stepper).

M10

Lens Horizontal Drive Shifts the lens horizontal position.

M11

Lens Vertical Drive

Shifts the lens vertical position.

M12

Optic Cooling Fan

Removes heat from the optics
unit.

M13

Fusing/Duplex Drive

Drives the fusing unit, the duplex
unit, and the paper exit rollers.

M14

Paper Feed

Drives all feed and transport
rollers in the paper tray unit.

M15

1st Lift

Raises the bottom plate in the 1st
paper tray.

M16

2nd Lift

Raises the bottom plate in the
2nd paper tray.

M17

Toner Collection

Transports the collected toner to
the toner collection bottle.

Comp

ent

ayo

t &

Descrip

FSM

2-7

A095/A096/A097

Summary of Contents for A095









































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for A095

Reviews:

Brands by name

Popular brands

Ricoh A095, Service Manual

Search results

Summary of Contents for A095

Reviews:

Brands by name

Popular brands