14
IQ9500 Installation Manual
4.0
Programming the Scale
4.1
Item Code Storage
Code numbers allow you to store information for the
parts that are counted most frequently. This eliminates
the need for re-entering data for each of these parts
during part count. Up to 200 item code numbers can
be programmed on your IQ9500 counting scale.
Section 4.1.1 details the procedure for storing the unit
weight, tare weight, quantity, part number, part name,
setpoints, and lot number with an item code. You can
enter all of this information for each item code or only
the data pertinent to your application. For example, if
you only want to store only the unit and tare weights,
you can bypass Steps 5 through 13 and go to Step 14.
4.1.1
Program Unit Weight, Tare Weight, Quantity, Part
Number, Part Name, Setpoints, and Lot Number
1. Press
MODE
key to enter program mode. The
MODE
annunciator will illuminate, the
WEIGHT
display will read
ProG
,
and the
QUANTITY
display will read
C XX
(
XX
repre-
sents the number of item codes stored in the
IQ9500 memory).
2. Enter the item code number (up to 16 digits)
and press the
CODE
key. All displays will
show zeros
.
If you want the item to be
alphanumeric then you will need to press the
.
(decimal) key to enter the characters using the
Teraoka Code (refer to Section 9.1). After
entering all of the characters, press the
CODE
key to store the item code.
NOTE:
If the
QUANTITY
display shows
CLEAr
, the
code number is already stored in memory. Press the
CODE
key a second time to modify the stored data or
press the
CLEAR
key to delete the item code and
stored data.
3. Enter tare weight (refer to Section 3.1).
4. Enter unit weight value (refer to Section 3.3).
5. Press
NET/GROSS
key to enter initial
quantity in stock for this item. The
QUANTITY
display will prompt
InVEnt
and
UNIT
-
WEIGHT
display will be
0
. Using the numeric keypad,
enter the number of pieces that the initial
inventory will contain and then press the
NET/GROSS
key a second time to store the
information.
6. Press the
–
key to enter the part number (16
characters maximum).
7. Use the Teraoka Code to enter the part
number (refer to Section 9.1). Press the
*
key
to store the part number.
8. Press
CODE
key to enter the part name (20
characters maximum).
9. Use the Teraoka Code to enter the part name
(refer to Section 9.1). Press the
CODE
key to
store the part number.
10. Press the
+
key to check Setpoint 1. The
WEIGHT
display will prompt
SEt 1
and the
QUANTITY
display shows the value of
Setpoint 1.
NOTE:
The
IQ9500
can store up to six setpoints
which are determined by Specification 18, bits 0
through 2.
11. Enter setpoint value and press
+
key to save.
NOTES:
• When entering weight setpoints, be sure that you
enter in the weight values with decimal point and all
leading and trailing zeros.
• All percentage values must be rounded to the
nearest whole number, fractional percentages are
not allowed.
• SPEC 7, bits 0 and 1 (Setpoint Type) determine
what kind of value you have entered. (Refer to
Table 4-1.)
12. Repeat Steps 10 and 11 for Setpoints 2
through 6.
13. Press the
CLEAR
key to enter the lot number.
Use the Teraoka Code (refer to Section 9.1) to
enter the lot number. Press the
*
key to store
the lot number.
14. Press
*
key to store all of the data entered with
this item code. The display will go back to
Step 1 but the number in the
QUANTITY
display will have been incremented by one.
15. Press
MODE
key to exit the program mode.
