19
SELECTION OF THE FUNCTIONS
Setting the selection of function (dip – switch) and the adjusting device (trimmer) present
in the control unit, several types of functioning are possible. MINI TS is supplied with the
following settings:
- Wind threshold at 30 Km/h
- Opening time at maximum = 7 min.
- Closing time at maximum = 7 min
- All the dip on off (
NOTE: to the Dip 4 are not associated functions)
- Light 2 threshold (intermediate)
Applying several devices for “environmental” control (anemometer, sensor of luminous
intensity, rain sensor), it is possible to execute some furtheradjustments, some of them by
acting directly on the card.
SETTING OF THE WIND ALARM THRESHOLD
safety threshold is set at an intermediate value of the velocity of the wind of 30 Km/h.
This velocity can be changed from 0 to 60 Km/h acting on the adjusting device (trimmer)
present on the card, as represented on the picture below:
Increase of the safety threshold
Decrease of the safety threshold
ATTENTION: the condition “open sunshade” is satisfied only in the case in which no
alarm is present. The presence of an alarm would immediately close the
sunshade and would block every type of external control for 7 minutes;
in this way the sunshade would rest closed, waiting for the output from
this state.
ATTENTION: during the installation, to avoid waiting the 7 minutes of the alarm
anytime one of the security sensors would intervene, it is possible
to reset the normal functioning of the control unit pressing the little
learning key once the sunshade is completely closed.
AUTOMATIC REOPENING
Acting on the dip – switch 1, once closed the sunshade cause of the alarm condition
“presence of strong wind” detected by the anemometer or “presence of water” detected by
the rain sensor and passed the 7 minutes from the last detection above the safety
threshold, it is possible to select:
• if you want that the sunshade is automatically reopened to the coming back
of the normal conditions (position ON)
• if it must remain closed waiting for an order coming from the mechanical
buttons (position OFF).
ATTENTION: with dip – switch 1 on , the control unit brings back the
sunshade on the position that it had before the alarm.
ATTENTION: in presence of the light sensor, the control given by it has
the priority on the state of the dip – switch 1. So, if the
dip – switch 1 is on OFF and there is intense light (over the opening
threshold), the sunshade will be reopened.
Step by step/ dead man functioning
ATTENTION: THIS SELECTION OF FUNCTIONING IS VALID ONLY AND EXCLUSIVELY FOR
THE CONTROLS GIVEN BY MECHANICAL BUTTONS
Acting on dip – switch 2, represented on the picture nearby and present on
the electronic card, it is possible to choose:
STEP BY STEP:
if you desire that the sunshade is totally open (close) with the
simple pressure of the opening (closing) button (position
ON)
.
DEAD MAN CONTROL:
if you prefer that the opening (closing) is directly
connected to the pressure of the relative button, so
stopping at its release (position
OFF)
.
SETTING OF THE LIGHT THRESHOLD
Acting on the jumper it is possible to choose the light threshold of automatic opening/closing
of the sunshade.
The green led present on the card allows to understand the level of light received by the
sensor.
Green led turned off, level of light under the closing threshold, it means that the sunshade
would automatically close for absence of light.
Green led blinks slowly, the level of light finds itself between the opening threshold and
closing threshold, so the sunshade maintains its position.
Green led blinks rapidly, the level of light finds itself above of the opening threshold, it
means that the sunshade will automatically open only if it finds itself on close position.
If it finds itself on any intermediate position it does not open because it is supposed that this
position has been manually reached.
Light
threshold 1
Light
threshold 2
Light
threshold 3
Reserved
-
Light threshold 1:
with this setting of the light threshold, the sunshade will automatically
open and close with little luminous intensity. This means that the sunshade will open early
in the morning and close late in the evening.
-
Light threshold 2 :
with this setting of the light threshold the sunshade will automatically
open with a luminous intensity higher than the threshold nr.1, that corresponds to a more
late opening of the sunshade and automatically close with little luminous intensity, the
same that this of the threshold nr.1; it means that the sunshade will close itself late in the
evening.
-
Light threshold nr. 3:
with this setting of the light threshold, the sunshade will
automatically open and close with a luminous intensity higher than this of threshold nr.
1. It means that the sunshade will open late in the morning and close early in the evening.
G
B
Summary of Contents for ACG2265
Page 30: ...30 NOTES ...
Page 31: ...31 NOTES ...
