RGB Omicrom FT Service Manual Download Page 27 | Manualshive

Page: 27 / 116

background image

OMICROM FT
SERVICE MANUAL

21 September 1998

2.20

again the optimum scaling.

2.4.6. Respiration messages.

During the normal operation of Omicrom FT monitor, it can show several alarm
messages regarding the respiration signal (P000PLAC20 board). These
messages are:

1) INTERNAL FAILURE

The self calibration has failed or it is not possible to
communicate with the respiration board.

2) CABLE OFF

The ECG cable is disconnected from the respiration
board.

3) LEAD OFF

The LL lead or RA lead or both leads are
disconnected.

4) APNEA ALARM

No breath has been detected during the apnea
alarm period selected.

2.4.7. System messages.

These are an special type of alarm messages that can produce a total system bad
performance, so when it is detected the normal operation is suspended and a
alarm screen is shown to indicate the type of failure. In this case it is necessary to
turn off the monitor and power on again. If the failure is repetitive contact RGB
MEDICAL DEVICES.

1) INTERNAL FAILURE F01

Illegal software opcode loaded at the display board
microprocessor (P000PLAC14 board).

2) INTERNAL FAILURE F02

Bad RAM addressing at the digital section of the
display board (P000PLAC14 board).

3) INTERNAL FAILURE F03

Memory error at the controtemp board
(P000PLAC04 board).

4) INTERNAL FAILURE F04

Illegal software opcode loaded in the controtemp
board microprocessor (P000PLAC04 board).

5) INTERNAL FAILURE F05

Bad RAM addressing at the digital section of the
controtemp board (P000PLAC04 board).

«
...
25
26
27
28
29
...
»

Summary of Contents for Omicrom FT





















































































































Reviews:

No comments

Related manuals for Omicrom FT

Brand: Salvis Pages: 40

Brand: IDEAL Pages: 2

Brand: Latchways Pages: 80

Brand: Kapriol Pages: 28

Brand: York Fitness Pages: 34

WJHD100 - DIGITAL DISC RECORDE

Brand: Panasonic Pages: 7

Brand: ZIGBEE Pages: 4

Brand: CAIRE Pages: 38

Brand: Caframo Pages: 72

Brand: Warehouse-lighting Pages: 3

Brand: Eagle Group Pages: 8

Brand: E2S Pages: 5

Brand: EuroLite Pages: 28

Brand: Launch Pages: 3

Brand: Launch Pages: 43

Brand: Launch Pages: 8

Brand: Launch Pages: 67

Brand: Launch Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands