REVV Dynamis 7-40 Owner'S Manual Download | Manualshive

Page: 16 / 36

background image

Revv Owner’s Manual - 16

FX Loop Connections

The FX loop connections are to be hooked up to external pedals or

effects units. The Send level will supply the signal required & needs to

be set accordingly with the send level control.

1 - 8 ohm cabinet

WITHOUT the provided 8 ohm combo speaker: In this

configuration, the provided speaker would be disconnected from the 8

ohm jack & the 8 ohm speaker cabinet would be plugged into that same

jack. The remaining 4 ohm speaker jacks MUST NOT be used. The pro-

vided speaker cannot be used in this configuration & must remain

disconnected.

1 - 4 ohm cabinet:

In this configuration, only one 4 ohm speaker cabinet

can be used with this amplifier. The provided 8 ohm combo speaker

MUST NOT be used, the remaining 4 ohm and 8 ohm speaker jacks

must also NOT be used.

2 – 4 ohm cabinets

cannot be run in parallel with this amplifier. This will

cause damage.

3.4

«
...
14
15
16
17
18
...
»

Summary of Contents for Dynamis 7-40





































Reviews:

No comments

Related manuals for Dynamis 7-40

MINAS-BL GP series

Brand: Panasonic Pages: 9

Brand: Pangea Audio Pages: 7

Brand: Radio Shack Pages: 20

Brand: Carson Pages: 12

Brand: Teac Pages: 4

Brand: ifi Pages: 14

Brand: Bang & Olufsen Pages: 12

Brand: MTX Pages: 6

Pro-Ject Tube Box SE

Brand: Pro-Ject Audio Systems Pages: 3

Brand: Cary Audio Design Pages: 20

Brand: NAD Pages: 2

MegaDipol MD300DX

Brand: NTI Pages: 2

Brand: Randall Pages: 6

Brand: Fender Pages: 18

Brand: DAPAudio Pages: 14

Brand: Linn Pages: 22

ZeroUno DAC-HPA

Brand: Canever Pages: 8

Brand: Inter-m Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands