16
17
English
English
6 USINg The CaMera
In-flight:
• Press the video button on the remote control
(2G)
briefly to record a video
(the LED will blink red). To end the recording, briefly press the button again
(the LED illuminates continuously red).
• Press the photo button on the remote control
(2B)
briefly to take a picture
(the LED will briefly illuminate green).
Inserting the memory card
• Inserting the memory card: Slide the memory card in with the gold contact towards
the front and carefully push it down into the card slot on the back of the camera
module until it engages. DO NOT USE FORCE!
(6A)
Downloading the data:
• Carefully press in the card until it unlocks, then pull it out of the slot.
DO NOT USE FORCE!
(6B)
• Now slide the card in with the gold contacts in front and with the small groove
on the card slot pointing towards the USB card reader. DO NOT USE FORCE!
(6C)
.
Now plug the card reader into a free USB port; it is recognised as a removable
data storage medium and images and videos can be used.
4 ChargINg The helICOPTer
Attention:
The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging
process must be constantly monitored. Always ensure that the charging process
takes place on a fireproof surface in a fire-resistant environment.
• Switch off the helicopter and the remote control
(4A/4B)
.
• Carefully insert the charging cable in the charge socket of the helicopter
(4C)
.
The plug must be gently inserted into the charging socket – DO NOT USE FORCE.
If the plug is not correctly inserted into the charging socket, the helicopter may
become damaged and, under certain circumstances, become an injury risk.
• The charging process lasts approx. 90 minutes and must be continuously monitored.
•
If the battery is fully charged, the LED of the charger illuminates red
(4D)
.
• Disconnect the battery from the charger and disconnect the charger from the outlet
after the charging is completed.
The helicopter can fly for approx. 5-7 minutes after a charge time of up to
90 minutes.
Warning notice:
The LiPo battery does not normally heat up while charging. If it
should become warm or even hot and/or changes to the surface begin to appear,
immediately discontinue the charging process!
5 STarT PreParaTION
Set the ON/OFF switch on the side of the helicopter to the "ON" position
(5A)
.
Place the helicopter on the ground so that the tail points toward you
(5B)
.
The thrust controller (the left control on the remote control) must point downward
before switching on
(5C)
. Then set the controller's ON/OFF switch to "ON"
and the Power LED blinks red
(5D)
. Now move the thrust control to full throttle and
back to zero; the remote control beeps once loudly and the power LED then illuminates
continuously. After a few seconds the helicopter is ready to start.
3 INSerTINg BaTTerIeS (reMOTe CONTrOl)
3A
Unscrew and remove
the cover.
3B
Insert 4 x 1.5 V AA
batteries and pay
attention to the polarity,
as shown in the battery
compartment.
3C
Close the battery
compartment cover.
2A
Power LED
2B
Button for photo
2C
Direction
controller
2D
Left-right trim
adjustment
2E
ON/OFF switch
2F
Thrust controller
2G
Button for video
2 reMOTe CONTrOl
1A
Stabiliser
1B
Tail rotor
1C
Landing skid
1D
Camera
1E
Headlamp
1F
Counter-rotating
blades
1G
Charge socket
1H
ON/OFF switch
1 helICOPTer
7 TrIM aDJUSTMeNT OF The CONTrOl
The correct trimming is a basic requirement for achieving fault-free flying from the
helicopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the helicopter approximately 0.5 to 1 metre in altitude.
Press the left/right trim adjustment to
the left until the helicopter no longer
rotates.
If the helicopter automatically
rotates clockwise…
Press the left/right trim adjustment to
the right until the helicopter no longer
rotates.
If the helicopter automatically
rotates anti-clockwise …
7B
7A
