background image

Chapter 9 Cautions and Maintenance 

 

9.1 Whiteboard 

 
For the interactive whiteboard that do not support normal marker (the product model 
is without “W”), please try not to use normal marker to write on the surface. Before 
cleaning, please shut down the computer and switch the projector into standby mode 
to make the dirt more obvious. In case of normal dirt, spay some water or detergent 
on the surface, then use the paper to wipe the dirt out. If you leave some ink trail by 
mistakenly using the fountain pen, please buy some special whiteboard detergent and 
spray it on the soft cloth to clean to surface. For cleaning the mark left by the 
permanent marker, first paint some ink of dry erase marker on the mark (the ink of dry 
erase marker can dissolve the ink of permanent marker), then use soft cloth to clean. 
If the mark still exists, spay some whiteboard detergent, and clean it out. 
 

 

 
2. For the interactive whiteboard that support normal marker, you can use normal 
whiteboard eraser and wet cloth to clean.   
 

 

 
3. Please do not use sharp or pointed objects to scratch the surface and frame, 
otherwise the scratched part may be damaged, and won’t work normally. During the 
usage, do not knock the surface fiercely to avoid the damage of whiteboard surface 
and electronic pen (writing pen). You can use sand wax to eliminate the scratch on the 
surface, and use dry cloth to clean out. 
 
4. Since the mobile stand (or the wall hanging parts) is designed only to support the 
weight of the whiteboard, please do not put the additional weight or pressure on the 
whiteboard. Please keep the whiteboard away from intense collision, shaking, 
pressing and do not install it by force, otherwise it may cause cracking, short circuit 
and surface distortion. 
 
5. Please do not use and install interactive whiteboard in dusty, foggy, wet and 
inclement environment. Keep it away from sharp object, heat source, corrosive 
chemicals, fire, and water. Please do not put the whiteboard in the outlet of hot air, 
otherwise the material will deteriorate and its life-span will be shortened. 

Prompt: Clean the frequently used whiteboard once a week to keep the best definition. 

Note:  Please do not use other organic solvent for cleaning. Otherwise it may 

permanently damage the surface.   

Summary of Contents for IQBoard ET































Reviews: