RESI®
Titel:
Manual RESI-DALI-ASCII
Datum
Seite
Von
14.02.2015
44
89
.
P
ro
p
ri
e
ta
ry
d
a
ta
,
co
m
p
a
n
y
co
n
fid
e
n
ti
a
l.
A
ll
r
ig
h
ts
re
s
e
rv
e
d
.
C
o
n
fié
à
tit
re
d
e
se
c
re
t
d
'e
n
tr
e
p
ri
s
e
.
T
o
u
s
d
ro
its
r
é
se
rv
é
s
.
C
o
m
u
n
ic
a
d
o
c
o
m
o
se
g
re
d
o
e
m
p
re
sa
ri
a
l.
R
e
se
rv
a
d
o
s
to
d
o
s
o
s
d
ir
e
ito
s.
C
o
n
fid
a
d
o
co
m
o
s
e
cr
e
to
i
n
d
u
s
tr
ia
l.
N
o
s
re
s
e
rv
a
m
o
s
t
o
d
o
s
l
o
s
d
e
re
c
h
o
s
.
.
.
W
e
it
e
rg
a
b
e
s
o
w
ie
V
e
r
v
ie
lf
ä
lt
ig
u
n
g
d
ie
s
e
r
U
n
te
rl
a
g
e
,
V
e
r-
w
e
rt
u
n
g
u
n
d
M
it
te
ilu
n
g
ih
re
s
In
h
a
lt
s
n
ic
h
t
g
e
s
ta
tt
e
t,
s
o
w
e
it
n
ic
h
t
a
u
s
d
r
ü
c
k
lic
h
z
u
g
e
s
ta
n
d
e
n
.
Z
u
w
id
e
rh
a
n
d
lu
n
g
e
n
v
e
r-
p
fl
ic
h
te
n
z
u
S
c
h
a
d
e
n
e
rs
a
tz
.
A
ll
e
R
e
c
h
te
v
o
rb
e
h
a
lt
e
n
,
in
s
b
e
-
s
o
n
d
e
re
fü
r
d
e
n
F
a
ll
d
e
r
P
a
te
n
te
rt
e
il
u
n
g
o
d
e
r
G
M
-E
in
tr
a
g
u
n
g
.
.
<GROUP> defines the affected DALI group according to the DALI standard. Group numbers from 0 to 15 are
allowed.
<ARCPOWER> defines the new brightness value for the lamps (0x00-0xFE or 0..254, 255 0xFF is used as a
mask value, refer to the DALI standard)
Samples:
Set lamp group 4 to maximum brightness level:
#GROUP
ARC:4=0xFE
CR
#OK
CR
#255,GARC:4=0xFE
CR
#255,OK
CR
7.49
New brightness for a single lamp
This command sends a new brightness value (Arc power) for a single lamp. The DALI standard supports 64
lamps.
Host long version:
#LAMP<SP>ARC<SP>POWER:<LAMP>=<ARCPOWER><CR> or
#<ADR>,LAMP<SP>ARC<SP>POWER:<LAMP>=<ARCPOWER><CR>
Host short version:
#LARC:<LAMP>=<ARCPOWER><CR> or #<ADR>,LARC:<LAMP>=<ARCPOWER><CR>
Answer:
If everything was ok with the command, the converter answers with
#OK<CR> or
#<ADR>,OK<CR>
If the DALI bus has no power, the converter answers with
#ERR:DALI<SP>BUS<SP>ERROR<CR> or #<ADR>,ERR:DALI<SP>BUS<SP>ERROR<CR>
If there is a syntax problem with the command, the converter answers with
#ERR:SYNTAX<SP>ERROR<CR> or #<ADR>,ERR:SYNTAX<SP>ERROR<CR>
<LAMP> represents the affected short address of the lamp according to the DALI standard. The short address
range 0 to 63 is allowed.
<ARCPOWER> defines the new brightness value for the lamp (0x00-0xFE or 0..254, 255 0xFF is used as a mask
value, refer to the DALI standard)
Samples:
Set maximum brightness for lamp 23:
#LAMP
ARC:23=0xFE
CR
#OK
CR
#255,LARC:23=0xFE
CR
#255,OK
CR
7.50
Recall scene in all lamps
This command recalls a previous stored scene in all lamps. The DALI standard supports 16 DALI scene per
lamp.
Host long version:
#ALL<SP>GOTO<SP>SCENE:<SCENE><CR> or
#<ADR>,ALL<SP>GOTO<SP>SCENE:<SCENE><CR>
Host short version:
#AGS:<SCENE><CR> or #<ADR>,AGS:<SCENE><CR>
