background image

Tactical ResQmax Operation Manual

35

Rescue Solutions International Inc. warrants to the original owner that if used, maintained, and 

stored according to the Manufacturer’s recommendations, the Tactical ResQmax is free from 

defects in material and workmanship for twelve (12) months from the date of the sale.

THIS WARRANTY IS LIMITED TO THE REPAIR AND REPLACEMENT OF PARTS AS NECESSARY, 

AND ANY NECESSARY LABOR AND SERVICES REQUIRED TO REPAIR OR REPLACE ANY PARTS 

TO RENDER THE DEVICE FREE OF DEFECTS.  THE SOLE OBLIGATION OF RESCUE SOLUTIONS 

INTERNATIONAL,  INC.  SHALL  BE   THE  REPAIR  OR  REPLACEMENT  OF THE  ResQmax  AND 

UNDER NO CIRCUMSTANCES SHALL RESCUE SOLUTIONS INTERNATIONAL, INC., ITS AGENTS, 

SUCCESSORS, OR ASSIGNS, BE LIABLE FOR ANY DIRECT, CONSEQUENTIAL, OR OTHER DAMAGES 

ARISING OUT OF ANY CLAIMED DEFECT IN THE DEVICE OR THE METHOD OF ITS USE. THIS 

WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, WHETHER RELATING 

TO FITNESS, MERCHANTABILITY, OR OTHERWISE. 

Except as to the express warranty set forth above, the Manufacturer disclaims any and all 

warranties and representations relating to the product. This limited warranty shall be governed 

by the laws of the State of Oregon. 

If you have a problem with your Tactical ResQmax, call 541-504-9300 or 800-709-5018 within 

90 days of discovery of the problem. You will be given instructions on where to send your 

Tactical ResQmax for repair or replacement. If the problem is covered by this warranty, Rescue 

Solutions International, Inc. will repair or replace your Tactical ResQmax, or otherwise notify 

you, within 30 days of receipt of the Tactical ResQmax.

Any actions for breach of warranty or breach of contract must be commenced within one year 

from the date of discovery of the breach.

Limited Warranty

Disclaimer

Rescue Solutions International, Inc. (RSI) has developed the Tactical ResQmax and all accessories in 

response to strong demand expressed by military, police and special forces teams worldwide. This 

product was created to fill an existing need as indicated by personnel and organizations whose 

members and employees knowingly and consciously are routinely engaged in very high risk and 

often life-threatening activities in the ordinary course of the performance of their duties.

RSI manufactures this equipment for use by, and at the discretion of, professionals aware of the 

risks associated with the use of this type of equipment, and who are properly trained in its use. 

This manual is intended only to educate the user in various aspects of this specific equipment. 

This manual does not undertake to teach, train, encourage, or condone any activities that 

may be associated with the use of this equipment. No equipment, brochure, manual, or other 

materials produced by RSI, nor the offer for sale or the sale itself of this equipment, is intended 

to induce any individual or organization to put personnel at personal risk.

RSI has no control over the training in the use of this equipment, the maintenance and servicing 

of this equipment, or the conditions under which this equipment is used. RSI disclaims any and 

all responsibility for any liability arising out of the use of this equipment, however caused.

Summary of Contents for Tactical ResQmax





































Reviews: