background image

 

 5 

  Safety Notes 

  General Safety Notes 

  All equipment undergoes final inspection and testing before leaving our factory. However, 

if equipment is damaged during shipping or through any other circumstances, it must not 

be used in service. Please check the device regularly for damages. Damaged parts 

should be replaced immediately. 

  All power/air/water/gas sources should be rated for the demands of the device as listed in 

the technical data sheets. Maximum ratings must not be exceeded. All VDE (Verein 

Deutscher Elektro-Ingenieure) standards should be followed. Equipment should be 

grounded according to standards. 

  Adherence to valid regulations regarding necessary checks (e.g. according to Accident 

Prevention & Insurance or electrical equipment) is exclusively taken over by the 

buyer/user of this product. 

  This device has been designated to be used only for its intended purpose. All other 

applications must be prohibited for safety reasons as otherwise the manufacturer’s 

warranty expires. 

  The device should be set-up in a clean, well-ventilated room, if necessary under a hood. 

  Supporting surfaces should be straight, flat and adequately stable. 

 

Don’t place anything on top of the machine. 

  To avoid injury, appropriate protection should be worn (e.g. gloves, safety glasses, safety 

shoes, hearing protection etc.) 

  If the machine is defective or working improperly it must be taken out of service. In case 

of further use of the machine the owner will be held responsible for any consequential 

damage. 

  To prevent accidents from water, fire or explosion, all power/air/water/gas sources should 

be turned off after working hours and during breaks, and secured against unauthorized 

access. 

  When carrying out maintenance works or repairs or when opening the device always turn 

off the main power switch and unplug the whole unit. 

  Repairs should be carried out only by the manufacturer or by qualified and certified 

personnel appointed according to chapter 7 

– warranty. 

  In case of leaking water out of housing or tank shut down device and call service. 

 

 

Summary of Contents for DUSTY COMFORT





















Reviews: