Regency P36E-LP4 Owners & Installation Manual Download Page 63

Page: 63 / 72

P36E-4 Zero Clearance Direct Vent Gas Fireplace

HAMPTON

OPTIONS

HAMPTON

CAST FACEPLATE

Remove top louver.

Open bottom louver.

Install the left side faceplate by pushing in at the side of the

rebox

and line up with top and bottom holes on side. Secure with screws,
tighten loosely.

Secure top of

faceplate with screw.

Repeat step 3 for the right side faceplate.

Secure bottom of

faceplate with screw.

Slide top piece of faceplate into side faceplates by

tting mounting

plates into brackets.

Push in both side faceplate pieces and completely tighten
screws.

Re-install top louver.

Close bottom louver.

Side piece

Faceplate

(Back View)

Bracket on back of

side faceplate.

Top piece

Faceplate

NOTE: Do not push in side faceplates all the

way, allow for room to place the top faceplate.

Mounting

Plate

Summary of Contents for P36E-LP4









































































Search results

Summary of Contents for P36E-LP4

Reviews:

Related manuals for P36E-LP4

Brands by name

Popular brands

Regency P36E-LP4, Owners & Installation Manual

Search results

Summary of Contents for P36E-LP4

Reviews:

Related manuals for P36E-LP4

Brands by name

Popular brands