Regency P36E-LP4 Owners & Installation Manual Download Page 62

Page: 62 / 72

P36E-4 Zero Clearance Direct Vent Gas Fireplace

Note:

The facing material has to go on after

the unit is set.

1) Remove Glass Door. Refer to P36E

Manual.

2) Remove 2 screws and bracket as indicated

(refer to Diagram 3).

3) Install On/Off switch (refer to Diagram 4).

4) Place bracket under the Flange. Secure

with 2 screws as indicated in Diagram 5.

5) Loosen the 3 x #8 Phillips Head Screws lo-

cated on the inside top of the outer frame of
the appliance (refer to Diagram 6).

Diagram 3

Remove

bracket

Remove both

screws

Diagram 4

On/Off

Switch

Control

Mounting

Bracket

Diagram 5

3 x #8

Phillips

Diagram 6

Note:

The Nailing Strips can be adjusted,

depending on the facing material (as indicated
in Diagram 8).

Optional

Install Optional 3-Panel Arch Door. (Refer
to Install 3-Panel Arch Door Instruction
Sheet).

10)

Change in Logo

Replace existing logo with Regency logo.

Attach Top and Side Support Frame

a) Ensure the Side Supports are aligned with

the corresponding hole on the Top Support
Frame, then secure with 1 screw.

b) Repeat step on the other side.

Diagram 8

1/2”

Facing

Material

1” Facing Material

Install Top Support Frame

Slide in the Top Support Frame using the
slots as a guide. Secure and re-tighten the
screws to the unit.

View of backside of Top Support

Frame.

Cut-Outs

a) Mount Side Support Frame to unit as

shown in Diagram 7, then secure with 2
screws on each side.

b) Repeat step on the other side.

Side Support Frame

Diagram 7

REGENCY

OPTIONS

Summary of Contents for P36E-LP4









































































Search results

Summary of Contents for P36E-LP4

Reviews:

Related manuals for P36E-LP4

Brands by name

Popular brands

Regency P36E-LP4, Owners & Installation Manual

Search results

Summary of Contents for P36E-LP4

Reviews:

Related manuals for P36E-LP4

Brands by name

Popular brands