Regency P36E-LP4 Owners & Installation Manual Download Page 61

Page: 61 / 72

P36E-4 Zero Clearance Direct Vent Gas Fireplace

TRIPOLI SCREEN DOOR

REGENCY

OPTIONS

When installing the optional Tripoli Screen Door Series, a non-combustible material 12" (305mm) above the unit and 6" (153mm)
on each side must be used (see Diagram 1).

The Tripoli Screen Door Series

also requires steel stud framing

above and on each side of the unit (refer to Diagram 1).

Min. 361/4”

(921mm)

Steel

Stud

Steel

Stud

Min.

14-1/4"

(362mm)P36

Min.

18-5/8"

(473mm)P36D

Option #2:

Fireplace with 1" (25mm) Facing Material

Stee

Stud

Stee

Stud

Min.

12"

(305mm)

Min. 6"

(153mm)

Min. 6"

(153mm)

P36

36-1/4"

(921mm)

36-1/4"

(921mm)

Framing & Mantle/Side Materials

Arch Screen

Non - Combustible

Material

27-1/2”

(699mm)

-7/8”

(784mm)

P36D

376-1/4"

(946mm)

Diagram 1

Min.

14-1/4"

(362mm)P36

Min. 361/4”

(921mm)

Steel

Stud

Steel

Stud

Min.

18-5/8"

(473mm)P36D

Option #1:

Fireplace with 1-1/2" (38mm) Facing Material

INSTALLATION NOTE:

The hearth material must be brought past the Tripoli frame all the way to the unit

face, so there will be no gap between the face and the actual fi replace.

* 'D' is Minimum height to combustible materials including the Minimum 2" (51mm) Top clearance to the Horizontal Vent.

OPTIONS

FRAMING DIMENSIONS

P36E

36-1/4”

(921mm)

36-1/4”

(921mm)

14-1/4”

(362mm)

46”*

(1168mm)

36-1/4”

(921mm)

36-1/4”

(921mm)

13-3/4”

(349mm)

46”

(1168mm)

Summary of Contents for P36E-LP4









































































Search results

Summary of Contents for P36E-LP4

Reviews:

Related manuals for P36E-LP4

Brands by name

Popular brands

Regency P36E-LP4, Owners & Installation Manual

Search results

Summary of Contents for P36E-LP4

Reviews:

Related manuals for P36E-LP4

Brands by name

Popular brands