manualshive.com logo in svg

Regency Contura RC500E, Owners & Installation Manual

Share
Download
Regency Contura RC500E Owners & Installation Manual Download Page 49

 

RC500E

  |    

49

installation

conversion kit from NG to LP

RC500E

919-882

09.12.18

CONVERSION KIT FROM NG TO LP

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Installation of LP Conversion Kit:

1.

 

Shut off  the gas and electrical supply.

2.  Lift off  the front safety screen (if installed) and open the front door 

(see details in manual).

3.  Remove the logs, and any media (if already installed).

4.  Remove the front grill - see manual.

5.  Remove the 3 screws holding the Burner Assembly to the fi rebox 

base. Lift burner straight up and lift out to remove.

6.  Loosen right side screw on pilot hood cover. Pivot cover to the 

left to reveal pilot hood.

/RRVHQVFUHZ

WARNING

This conversion kit shall be installed by a quali-
fi ed  service  agency  in  accordance  with  the 
manufacturer’s  instructions  and  all  applicable 
codes and requirements of the authority having 
jurisdiction. If these instructions is not followed 
exactly, a fi re, explosion or production of carbon 
monoxide may result causing property damage, 
personal injury or loss of life. The qualifi ed ser-
vice agency is responsible for the proper instal-
lation  of  this  kit. The  installation  is  not  proper 
and complete until the operation of the convert-
ed appliance is checked as specifi ed in the man-
ufacturer’s instructions supplied with the kit.

7.  Lift off  pilot cap to expose pilot orifi ce.

8.  Unscrew the pilot orifi ce with the supplied Allen key and replace 

with the LP pilot orifi ce in the kit --replace pilot cap.

LP Conversion Kit Contains: (Part #366-969)

Qty

Part #

Description

1

904-529

5/32" Allen Key

1

904-163

Burner Orifi ce #54

1

918-590

Label "Converted to LPG"

1

908-528

Red "LPG" label

1

910-101

LP Injector (Pilot Orifi ce)

1

911-011

Stepper Motor

1

919-882

Instruction Sheet

9.  Remove burner orifi ce with a 1/2" wrench and discard. Use another 

wrench to hold on to the elbow behind the orifi ce.

WRROWLS

Burner Orifi ce

10.  Reinstall new burner orifi ce LP stamped #54 and tighten.

11.   Open the lower access door by pulling open to the left. 

12.   Lift  off   component  access  cover  to  remove  (see  manual  for 

details).

Summary of Contents for Contura RC500E









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands