manualshive.com logo in svg

Regency Contura RC500E, Owners & Installation Manual

Share
Download
Regency Contura RC500E Owners & Installation Manual Download Page 20

20

     | 

RC500E

owner's information

1.  Turn  off  stove  and  allow  it  to  return  to  room 

temperature.

2. Lift off cast top and place on a soft surface.

1.  Turn  off  stove  and  allow  it  to  return  to  room 

temperature.

2. Lift off cast top and place on a soft surface.      
    Remove side safety screen.

tooltip

tooltip

tooltip

tooltip

3.  Remove  4  screws  from  each  light  assembly 

housing in locations shown below.

4. Lift housing off unit to replace bulb.
Note: Do not touch bulb with bare hands, use gloves 
or a tissue to handle bulb.

5. Reinstall 4 screws to secure each housing.

6. Reinstall cast top.

Top of Unit

accent light bulb  
replacement

outside side glass 
replacement

fan maintenance / replacement

If your fan requires maintenance or replacement, 
access to the fan is through the rear access panel 
on  the  back  of  the  unit. 

 NOTE: the unit MUST 

NOT be operated without the fan access panel 
securely in place and correctly sealed.

IMPORTANT:  These fans collect a lot of dust from 
within your home. Ensure you maintain these 
fan motors on a regular basis by vacuuming 
out the fan squirrel cages, around the motor, 
and around the grills on the back of the stove.

IMPORTANT

Disconnect power supply 

before servicing

WARNING: 

Electrical Grounding Instructions

This appliance is equipped with a 

three pronged (grounding) plug for 

your protection against shock haz-

ard and should be plugged directly 

into a properly grounded three-prong 

receptacle. Do not cut or remove the 

grounding prong from this plug.

1.  Shut unit off and allow to return to room tempera-

ture, shut off gas and electrical supply.

2.  Open lower door and remove lower access panel 

(see detailed instructions in this manual).

3. Disconnect gas line to allow removal of fan.

4.  Remove 2 screws to release fan and manoeuver 

fan to the right and then out of unit.

5. Replace fan (if necessary) and reverse steps 4-1.

3.  Remove  1  screw  in  location  shown  to  release 

side panel.

4. Slide side panel straight up to remove.

5. Bend out 4 tabs 90° until straight to release glass.

6.  Replace glass and secure by folding 4 tabs back 

in towards glass.

7. Reinstall panel with new glass.
      Note: line up panel with pin at base of unit - secure 

panel with one screw.

8. Reverse Step 2-1.

Summary of Contents for Contura RC500E









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands