manualshive.com logo in svg

Regency Fireplace Products Plateau PTO30, Owners & Installation Manual, Page: 8 / 52

Share
Download
Regency Fireplace Products Plateau PTO30 Owners & Installation Manual Download Page 8

8

 | 

Regency Plateau

®

 PTO30-11 Outdoor Gas Fireplace

 | 

8

installation

LOCATING YOUR   
OUTDOOR DECORATIVE GAS APPLIANCE

1.  When selecting a location for your decorative gas appliance, ensure that the clearances are met.

2.  This appliance must be installed in an open-air situation with natural ventilation, without stagnant 

areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural 
convection.

3.    Certain materials or items, when placed under or near the appliance, will be subjected to radiant 

heat and could become damaged.

4.  Typically an outdoor space is not enclosed but, any enclosure in which the appliance is used shall 

comply with one of the following:

     An enclosure with walls on all sides, but at least one permanent opening at ground level and no 

overhead cover.

 

Within a partial enclosure that includes an overhead cover and no more that two walls.

 

Within a partial enclosure that includes an overhead cover and more than two walls, the following 
shall apply:

 

  

 

• 

At least 25% of the total wall area is completely open, and 

 

  

 

• 

At least 30% of the remaining wall area is open and unrestricted

INSTALLATION   
CHECKLIST

    
If installing as PT060 (2 x PT030 end to end) 

you must repeat steps 2 - 5 for both units.

1. 

Locate appliance: 

 

a)  Refer to "Locating Your Outdoor decorative 

gas appliance" section

 

b)  Clearances  to  Combustibles  (Refer  to 

"Clearances" section)

 

c)  Framing & Finishing Requirements (Refer 

to "Framing & Finishing" section)

 

2.

  Drain Installation (recommended).

3. 

Install ON/OFF switch - ensure it is in the OFF 
position.

4.

  Make gas connections - test for leaks.

  

5.  

Install 4 "AA" batteries into each battery pack. 
This unit will not operate without AA batteries 
in place.

6.

  Install standard and optional features.  Refer to 

the following sections: 

 
    a. 

Glass Crystals

 

 b. 

Volcanic Stone Installation (optional)

 

c. 

Log Installation (optional)

 

d. 

Glass Surround Installation (optional)

 

 

7.

  Final check.

This includes:

1.

  Clocking  the  appliance  to  ensure  the  correct 

firing rate (rate noted on label), after burning 
appliance for 15 minutes.

2.

  If required, adjusting the primary air to ensure 

that the flame does not carbon.  First allow the 
unit to burn for 15-20 min. to stabilize.

CAUTION: Any alteration to the product that 
causes sooting or carboning that results in dam-
age is not the responsibility of the manufacturer.

30% or more in total of the remaining wall 
area is open and unrestricted.

Open side at least 25% of total wall area

*SEE IMPORTANT INSTALLATION NOTES NEXT PAGE

Summary of Contents for Plateau PTO30





















































Reviews:

No comments