Regency Fireplace Products Plateau PTO30 Owners & Installation Manual Download Page 12 | Manualshive

Page: 12 / 52

Regency Fireplace Products Plateau PTO30 Owners & Installation Manual Download Page 12

12

|

Regency Plateau

®

PTO30-11 Outdoor Gas Fireplace

|

12

installation

1

PTO30/PTO50 OUTDOOR SERIES

920-390

04.09.21

PTO30/PTO50 - Two (2) ventilation grills are required for all enclosures. The ventilation grill(s) must be placed at either end as shown to allow the air
to circulate from one end to the other. This is to alleviate moisture and allow for air to circulate. Minimum recommended size 20" sq (508 mm²) ea.

PTO60/PTO80/PTO100 - Four (4) ventilation grills are required for all enclosures. Two (2) upper and two (2) lower ventilation grills are required for
all enclosures.
This is to alleviate moisture and allow for air to circulate. Minimum recommended size: 20" sq. (508 mm²) ea.

If using the grills offered by Regency (supplied), follow the instructions noted below:
Frame the opening for the upper vent at 16" x 1-1/4" - secure the upper vent to the framing with 6 screws.

Frame the opening for the lower vent at 8" x 2-7/8" - secure the lower vent with 10 screws.

We highly recommend installing these upper (PTO60/PTO80/PTO100) and lower grills (PTO30/PTO50/PTO60/PTO80/PTO100) at either end of the
framed structure to allow the air to circulate from one end to the other.
Note: If purchasing grills elsewhere, ensure the minimum recommended size of 20"sq. (508 mm²) each is met.

PTO30/PTO50 Optional grills Includes 2 x 377-061 Lower vent (Kit part # 377-946)
PTO60/PTO80/PTO100 Optional grills Includes 2 x 377-061 Lower vent & 2 x 377-060 Upper Vent (Kit part # 377-948)

PTO30/PTO50 ENCLOSURE VENT INSTALLATION

Upper vent

# 377-060

Lower vent

# 377-061

Flange

Flange

Note:

Finishing material can be brought over the flange of the ventilation grills to ensure a clean look.

Upper Vent

Grill

Lower Vent

Grill

Upper Vent

Grill

Lower
Vent Grill

ENCLOSURE VENT INSTALLATION

«
...
10
11
12
13
14
...
»

Summary of Contents for Plateau PTO30





















































Reviews:

No comments