Regency Fireplace Products Plateau PTO30 Owners & Installation Manual Download Page 36 | Manualshive

Page: 36 / 52

Regency Fireplace Products Plateau PTO30 Owners & Installation Manual Download Page 36

36

|

Regency Plateau

®

PTO30-11 Outdoor Gas Fireplace

|

36

installation

919-144

03/17/14

1.

Position each corner vertical support on lower frame and secure with

four (4) screws each.

2.

Place top frame onto corner vertical supports and secure to each sup-

port with four (4) screws.

3.

Install six (6) inner vertical supports - secure each support with two (2)

screws to top frame and two (2) screws to bottom frame.

4.

Install four (4) outer vertical supports - secure each support with two (2)

screws to top frame and two (2) screws to bottom frame.

Diagram 1 - Corner supports on lower frame.

Diagram 2 - Corner supports screw locations

Diagram 3 - Corner supports with top frame

Diagram 4 - Inside vertical supports

Diagram 5 - Inside vertical support

screw locations

Diagram 6 - Outside vertical supports

vent

vent

vent

vent

2

OUTDOOR BURNER

«
...
34
35
36
37
38
...
»

Summary of Contents for Plateau PTO30





















































Reviews:

No comments