Regency Fireplace Products Plateau PTO30 Owners & Installation Manual Download Page 19 | Manualshive

Page: 19 / 52

Regency Fireplace Products Plateau PTO30 Owners & Installation Manual Download Page 19

Regency Plateau

®

PTO30-11 Outdoor Gas Fireplace

e |

19

19

|

installation

LP CONVERSION

1

PTO30 / PTO30-1

919-038b

12/29/20

CONVERSION FROM NG TO LP

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Each Kit contains one LP Conversion Kit

Conversion Kit # 376-969 Contains:
Qty.

Part #

Description

1

904-655

Burner Orifice #45

1

910-101

Pilot Orifice LP

1

904-529

5/32" Allen Key

1

918-590

Decal "Converted

to LPG"

1

908-528

Red "LP" label

1

911-009

Hi/Lo conversion LP For 886

1

919-038

Instruction Sheet

1.

Remove table top(if installed) by lifting up and off, use caution if glass

surround is in place.

2.

Remove glass crystals, garden stones, and log set, if installed.

4.

Slide burner away from burner orifice and lift up to remove burner

assembly.
* Proceed to Step 7.

Turn the unit off and allow to cool to room temperature.
Turn off gas supply.

Pilot Cap

Pilot Cap

Burner orifice

Burner orifice

5.

Locate and remove 9 screws to remove the burner tray.

3.

Locate and remove 2 screws at each end of burner assembly - see loca-

tions in Diagram 1 below.

6.

Lift burner tray off.

«
...
17
18
19
20
21
...
»

Summary of Contents for Plateau PTO30





















































Reviews:

No comments