Regency Fireplace Products Cascades I2500 Owners & Installation Manual Download Page 10 | Manualshive

Page: 10 / 40

background image

10

|

Regency I2500M

|

10

installation

STAINLESS STEEL SMOKE DEFLECTOR INSTALLATION

The stainless smoke deflector is located in the upper front area of the firebox. The deflector is held in place with 2 bolts
Prior to the first fire, ensure deflector is seated properly and secured with 2 hand tightened bolts.

To replace the deflector, loosen off both bolts and slide deflector upward and out. Install new deflector and hand tighten bolts. Ensure positive location of
the deflector prior to hand tightening.

WARNING:

Operation of the unit with out proper installation of smoke deflector will void warranty.

S

moke deflector installed with 2 bolts.

Note:

This is a view from the back of the unit

through the top.

Smoke deflector is installed through the door

opening in location shown in diagram

S

moke deflector

Ensure deflector is seated so bolts are situated

at the top of the keyhole before tightening.

«
...
8
9
10
11
12
...
»

Summary of Contents for Cascades I2500









































Reviews:

No comments

Related manuals for Cascades I2500

Cleveland CMSF-1/0310

Brand: Warm House Pages: 19

Brand: Valor Fires Pages: 28

MANDALAY Series

Brand: Warnock Hersey Pages: 38

Superior Fireplaces Merit WRT2042WS

Brand: IHP Pages: 24

Brand: Heatilator Pages: 3

Brand: United States Stove Company Pages: 20

Brand: Napoleon Pages: 4

Brand: Monessen Hearth Pages: 44

E-SLIM LINEAR 1200/450 I

Brand: Faber Pages: 31

Abbotsford 064-4015-0

Brand: Canvas Pages: 104

Brand: QualityCraft Pages: 12

Brand: ADURO Pages: 14

Brand: EdilKamin Pages: 19

Brand: Lennox Hearth Products Pages: 2

Brand: Country Living Pages: 10

Brand: Char-Broil Pages: 8

Brand: Char-Broil Pages: 8

Brand: IHP Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands