RedWing RC Edge 540 v3 Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 20

background image

STRONG DESIGNS RW EDGE 540V3 30CC

20

Receiver and Setup

The receiver will typically be located behind the
wing tube support or on the rudder servo tray
with the batteries placed to achieve the proper
balance of the model. Make all connections and
use a soft mounting to help isolate from
vibration.

Center of Gravity

For your first flights set the CG 5.25” from the
leading edge at the root of the wing. This is
near the front of the wing tube and will be close
to neutral. After checking the CG in flight you
can adjust for your personal flying style.

Control throws: -- DR/Expo --

LOW

MED

HIGH

AIL      1.75”/30%       2.75”/40%              4”/60%
ELE        2.5”/30%      3.25”/ 40%              4”/55%
RUD      2.5”/20%           3”/ 30%           4.25”/40%

NOTES:

______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________
______________________________

«
...
18
19
20

Summary of Contents for Edge 540 v3





















Reviews:

No comments

Related manuals for Edge 540 v3

Brand: E-FLITE Pages: 17

Habu 32 EDF ARF

Brand: E-FLITE Pages: 56

Brand: Xray Pages: 48

Brand: Rage RC Pages: 16

SPINNER MISSILE XL

Brand: Rage Pages: 2

Steaman Aerobatic Biplane

Brand: REVELL Pages: 12

Brand: P&M Aviation Pages: 95

Lights & Sounds

Brand: Learning Resources Pages: 2

Brand: GAME OF BRICKS Pages: 31

MAN F2000 Evolution

Brand: ROBBE Pages: 44

He 219 exterior

Brand: Eduard Pages: 2

Brand: Funkey Pages: 6

Wireless Plus Set Duo 20010109

Brand: Carerra Pages: 52

Beach Bungalow House

Brand: Barbie Pages: 6

Brand: T3 Simulations Pages: 8

Brand: Clas Ohlson Pages: 5

HK-TF2357A-2.4G

Brand: Clas Ohlson Pages: 36

E-flite UMX NIGHT VAPOR BNF

Brand: Horizon Hobby Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands