background image

RTP-805

13

ENG
UKR
KAZ

Removing and installing the appliance lid 

(scheme 

A4

, p. 5)

Press the lidr latch and pull it up. Open the lid to 45°, press the 

lid release button on the back of the thermopot, and remove the 

lid.

To reattach the lid, insert the metal pin on the back of the lid into 

the groove on the body, holding the lid at an angle 45°. Gently 

check if the lid is installed securely.

Daily care

It is recommended to discharge the remaining water completely 

every day, otherwise its taste will deteriorate with refilling, and 

probability of scale occurrence on the walls of the tank will in-

crease. After water discharge, wipe the tank walls with a clean 

descaling cloth.

Body and lid cleaning

Clean the appliance body and the lid with a damp soft cloth oc-

casionally. Remove gross contamination with mild detergents. Dry 

the appliance completely before use.

Cleaning the water tank

Clean the water tank with a damp sponge. Do not use ordinary 

detergents: they may leave unpleasant odour and spoil taste of 

water.

Descaling

During operation, depending on composition of the water used, 

plaque and scale may form on the heating element and the in-

ternal walls of the appliance. Use special non-abrasive agents for 

cleaning and descaling kitchen appliances to remove them. Follow 

the cleaning agent manufacturer's instructions. After cleaning, 

discharge the solution and rinse the tank thoroughly with cold 

water. Wipe the water tank with a damp cloth. To eliminate unpleas-

ant odour of the cleaning agent, fill the water tank up to the 

maximum mark, boil it and then drain it.

Storage and transportation

Before repeated operation or storage completely dry all parts of 

the appliance. Store the assembled appliance in a dry, ventilated 

place away from heating appliances and direct sunlight.
During transportation and storage, do not expose the device to 

mechanical stress, that may lead to damage of the device and/or 

violation of the package integrity.
Keep the device package away from water and other liquids.

IV. BEFORE CONTACTING SERVICE 

CENTER

Problem

Possible cause

Solution 

The appliance does not 

switch on

No power supply

Connect  the  appliance  to  a 

properly working electric socket

Error message is dis-

played on the screen 

“Е1”, “Е3” or “E7”

System error

Unplug  the  appliance,  after 

5 minutes, plug it back into the 

mains. If the appliance still doesn’t 

work, apply to the service center

Summary of Contents for RTP-805

















Reviews: