background image

 

 

3

              

 !

                     SAFETY REGULATIONS             

(1)   The 

Topdresser 1005/ 1010

 is built 

solely for spreading small-grained

, loose 

material such as sand, small granular material or similar products.

 

 

 

Any other usage is not in accordance with the indicated use. The manufacturer 

 

does not answer for any damage resulting from incorrect usage

. The user alone 

 

has to incur the risk.

 

 

 

Usage in accordance with the intended use also includes 

compliance with the 

 

manufacturer’s conditions of operation, maintenance and repair

.

 

 

(2)   

The spreader is built according to prior art and operationally reliable; however, 

 

the spreader could put life and limb of the operator or of third persons at risk

 if it 

 

is not used, maintained and repaired by persons who are familiar with it and have 

 

been informed of the dangers.

 

 

(3)   

Any person who, in the plant of the user, is responsible for the operation, 

 

maintenance and repair of the spreader, 

must have read and understood

 the 

 

operating instructions and, in particular, this chapter, 

Safety Regulations.

 

 

 

Detach the spreader

 from the towing vehicle during maintenance and service work.

 

  

Only 

use 

original spare

 parts from the manufacturer for repairs.

 

 

 

Alongside the references in these operating instructions

, the general regulations 

 

for safety and for prevention of accidents must be observed.

 

 

 

When using public roads, the corresponding provisions (e.g. StVZO) will be  

 in 

force.

 

 

 

Accompanying persons are not allowed

 ! 

 

(4)   

A spreader may only be towed along public roads once it 

holds the necessary 

 registration

. Complete road-worthiness certificate, licensing permit and the  

 

additional safety facilities necessary for this (Lighting set, wheel chocks)

#

 are  

 

obtainable on request of the customer. 

 

(5)  The operator is obliged to 

check the spreader for any external damage or  

 

failure before putting it into operation.

 Any changes (including operating  

 

performance) which might affect safety must immediately be remedied. Changes 

 

to and rebuilding of the spreader (other than changes allowed by the  

 

manufacturer) are, for reasons of safety, not allowed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for RINK 1005















Reviews: