Raypak Low NOx Series Installation And Operation Manual Download Page 25

Page: 25 / 46

Status and Diagnostics

The digital models are programmed to display a variety

of status and diagnostic messages, depending on the

operating conditions.
The following heat status messages are displayed in Pool,

Spa, and Remote modes when there are no active fault

conditions.

Display

Condition

Heating

Call for heat established, flame present.

Spark

Spark operating.

No Demand

Heat demand is satisfied.

Table M. Heater Status Messages - No Active Faults

The following conditions are displayed in Pool, Spa and

Remote modes when there are active fault conditions.

Display

Condition

Sensor Failure

Thermistor temperatures disagree by

more than 2°F (1°C)

Sensor Open

Thermistor sensor failed open. Below

-20°F (-29°C).

Sensor Short

Thermistor sensor failed short. Above

217°F (103°C).

Flame w/o CFH

Board is sensing flame when

both main and pilot valves are

commanded shut.

MV Output Fault

Main gas valve output is not in

commanded state.

Lo NOx Tab Fault

Voltage is sensed at the Lo NOx

terminal on a non-Lo NOx Heater (Lo

NOx tab is intact)

Internal Fault

Board fault, replace board.

EEPROM Fault

Memory fault, reset set points,

replace board if fault does not clear.

Clock/Fireman Sw

Time clock/fireman switch circuit is

open.

Low Temp

Lockout

Water temperature below 36°F (2°C).

Table N. Heater Status Messages - Active Faults

The following conditions are displayed only while there is a

demand for heat present.

Display

Condition

Water Sw Open

Water pressure switch open.

Vent/Field

Sw #1

Vent spill switch/field switch #1 open.

Hi Limit 1 Fault

High limit 1 open.

Hi Limit 2 Fault

High limit 2 open.

Rollout Sw Open

Rollout switch open.

Flow/Field SW #2

Field-supplied flow switch/field switch

#2 open.

Fan Lockout

3 fan switch faults within same heat

demand cycle, power must be cycled

to clear the fault

Fan 5 Min Delay

Heater shut down for 5 minutes

because LoNOx fan switch didn't close

Ignition Lockout

(Propane Tab

Broken)

Alternating with “No pilot sensed”

- Pilot flame not established within the

required time (15 sec or 90 sec).

Alternating with “Main Ign Failure”

- Pilot flame lost during the 8 second

trial to ignite the main burner.

Ignition Failure

(Propane Tab Not

Broken)

Alternating with “No pilot sensed”

- Pilot flame not established within 90

seconds.

Ign 6min Delay

(Propane Tab Not

Broken)

Alternating with “Main Ign Failure”

- Pilot flame lost 4 times within the 8

second trial to ignite the main burner.

Heater will lockout for 6 minutes before

retrying.

Table O. Heater Status Messages - Demand for Heat

6000.592A_PoolSpa_LoNOx.indd 25

11/22/2019 10:44:49 AM

Summary of Contents for Low NOx Series















































Search results

Summary of Contents for Low NOx Series

Reviews:

Related manuals for Low NOx Series

Brands by name

Popular brands

Raypak Low NOx Series, Installation And Operation Manual

Search results

Summary of Contents for Low NOx Series

Reviews:

Related manuals for Low NOx Series

Brands by name

Popular brands