Raypak Low NOx Series Installation And Operation Manual Download Page 22

Page: 22 / 46

7. CONTROLS

F10639-3

PRESSURE SWITCH

TEMP SENSOR

HL1 - HIGH LIMIT

HL2 - HIGH LIMIT

UNITHERM

GOVERNOR

PILOT

AIR PRESSURE

SWITCH

PROTEK

SHIELD

ASSY

MANUAL

RESET

ROLL-OUT

SWITCH

CONTROL

BEZEL

GAS

VALVE

Figure 34. Location of Controls (View One)

F10639-2

BLOWER

DRAIN PLUG IN

REAR HEADER

Figure 35. Location of Controls (View Two)

Control Panel Removal

1. Remove screw from front door. Set aside door for

serviceability.

Remove (4) screws from sides of control panel.

3. Rotate control panel down until panel stops. Do not

force.

NOTE:

Caution must be used to not damage controls

or wiring.

F10647-3

KNURLED

SCREW

Figure 36. Knurled Screw Location

Control Adjustments

The pool heater touchpad, located on the upper front

panel of the heater, allows the user to select either POOL

or SPA operation, and to adjust the setpoint temperature.

The LCD display window indicates the mode (OFF, SPA,

POOL) and the actual water temperature. A manual power

switch provided below the touchpad turns the control

power ON or OFF. See

Figure 37.

TEMP

MODE

OFF

LCD DISPLAY

TEMP ADJUST BUTTONS

MODE BUTTON

Figure 37. Control Adjustments

6000.592A_PoolSpa_LoNOx.indd 22

11/22/2019 10:44:47 AM

Summary of Contents for Low NOx Series















































Search results

Summary of Contents for Low NOx Series

Reviews:

Related manuals for Low NOx Series

Brands by name

Popular brands

Raypak Low NOx Series, Installation And Operation Manual

Search results

Summary of Contents for Low NOx Series

Reviews:

Related manuals for Low NOx Series

Brands by name

Popular brands