Raypak Low NOx Series Installation And Operation Manual Download Page 8

Page: 8 / 46

Description

Location

Distance

in. (mm)

3-1/2" (89 mm) thick

masonry walls without

ventilated air space

Back

9 (229)

Right

9 (229)

Left

9 (229)

Vent

5 (127)

Indoor Top

39 (991)

Outdoor Top

Unobstructed

b. 1/2" (13 mm)insulation

board over 1" (25 mm)

glass fiber or mineral

wool batts

Back

6 (152)

Right

6 (152)

Left

6 (152)

Vent

3 (76)

Indoor Top

30 (762)

Outdoor Top

Unobstructed

c. 0.024 sheet metal over

1" (25 mm) glass fiber

or mineral wool batts

reinforced with wire on

rear face with ventilated

air space

Back

4 (102)

Right

4 (102)

Left

4 (102)

Vent

3 (76)

Indoor Top

24 (610)

Outdoor Top

Unobstructed

d. 3-1/2" (89 mm) thick

masonry wall with

ventilated air space

Back

6 (152)

Right

6 (152)

Left

6 (152)

Vent

6 (152)

Indoor Top

39 (991)

Outdoor Top

Unobstructed

e. 0.024 sheet metal with

ventilated air space

Back

4 (102)

Right

4 (102)

Left

4 (102)

Vent

2 (51)

Indoor Top

24 (610)

Outdoor Top

Unobstructed

f. 1/2" (13 mm) thick

insulation board with

ventilated air space

Back

4 (102)

Right

4 (102)

Left

4 (102)

Vent

3 (76)

Indoor Top

24 (610)

Outdoor Top

Unobstructed

0.024 sheet metal with

ventilated air space over

0.024 sheet metal with

ventilated air space.

Back

4 (102)

Right

4 (102)

Left

4 (102)

Vent

3 (76)

Indoor Top

24 (610)

Outdoor Top

Unobstructed

1" (25 mm) glass fiber

or mineral wool batts

sandwiched between two

sheets 0.024 sheet metal

with ventilated air space

Back

4 (102)

Right

4 (102)

Left

4 (102)

Vent

3 (76)

Indoor Top

24 (610)

Outdoor Top

Unobstructed

Derived from National Fuel Gas Code, Table 10.2.3

Table C. Reduction of Clearances to Protected Surfaces

Heaters must not be installed under an overhang of less

than three 3' (0.9 m) from the top of the heater. Three sides

must be open in the area under the overhang. Roof water

drainage must be diverted away from the heaters installed

under overhangs with the use of gutters.

For U.S. installations,

the point from where the flue

products exit the heater must be a minimum of 4' (1.2 m)

below, 4' (1.2 m) horizontally from, or 1' (0.3 m) above any

door, window or gravity inlet into any building. The top

surface of the heater shall be at least 3' (0.9 m) above

any forced air inlet, or intake ducts located within 10' (3 m)

horizontally.

For Canadian installations,

pool heaters shall not be

installed with the top of the vent assembly within 10' (3 m)

below, or to either side, of any opening into the building.

Refer to the latest revisions of CAN/CSA-B149.
A minimum of 6

(1.8 m) is required from the heater to an

inside corner wall for proper outdoor venting.

For installations in Florida and Texas,

that must comply

with the Florida or Texas Building Code, follow the directions

shown in

Figure 7

for the installation of hurricane tie-down

brackets for all models.

Forced Air Inlet

4' (1.2 m)

Minimum

3' (0.9 m)

Minimum

10' (3 m)

Minimum

1' (0.3 m)

Minimum

4' (1.2 m)

Minimum

4' (1.2 m)

Minimum

Figure 3.

Clearances

Pagoda Top Installation

1. Insert tabs into keyhole (4 places). See

Figure 4

detail A.

Snap tabs into keyholes so as not to pull out. See

Figure 4

, detail B.

OUTDOOR TOP

(SHIPPED LOOSE WITH HEATER)

DETAIL A

DETAIL B

Figure 4. Outdoor Top Installation

Indoor Heater Installation

The heater is also design-certified for indoor installation

when equipped with the approved drafthood.

6000.592A_PoolSpa_LoNOx.indd 8

11/22/2019 10:44:38 AM

Summary of Contents for Low NOx Series















































Search results

Summary of Contents for Low NOx Series

Reviews:

Related manuals for Low NOx Series

Brands by name

Popular brands

Raypak Low NOx Series, Installation And Operation Manual

Search results

Summary of Contents for Low NOx Series

Reviews:

Related manuals for Low NOx Series

Brands by name

Popular brands