Raypak Low NOx Series Installation And Operation Manual Download Page 15

Page: 15 / 46

Flow GPM

(lpm)

Pressure Drop

Ft. of Head (m of Head)

207A

267A

337A

407A

20 (75)

TBD

30 (113)

TBD

40 (151)

TBD

50 (189)

TBD

60 (227)

TBD

70 (265)

TBD

80 (303)

TBD

90 (340)

TBD

100 (378)

TBD

Table L. Brass Heat Exchanger Pressure Drop - ASME

Models - UG Fully Open

NOTE:

Table capacity is based on Schedule 40 black

iron pipe. For capacity using other material, consult

local codes.

Brass Headers (ASME Models)

Heater must be located so that any water leaks will not

damage the structure of adjacent area. Before attaching

the ProTek Shield Adapter to the inlet connection and the

2-inch unions, make sure the O-rings are properly seated

in the grooves. Use Aqualube or equivalent non-petroleum-

based lubricant on the O-ring.

Hand tighten the unions

Glue PVC piping directly to the unions.

F10664

HEADER

O-RING

HEADER FLANGE

(CPVC)

HEADER FLANGE NUT

(CPVC)

PLUMBING

PROTEK SHIELD

ASSEMBLY

Figure 18. Inlet/Outlet Header – Brass

NOTE:

Some jurisdictions require the addition of a flow

switch on ASME installations. Kit # TBD can be ordered

that will allow a standard ASME unit to comply with the

code requirements.

ProTek Shield Assembly

This heater is equipped with a ProTek Shield Assembly

(located under the inlet connection on polymer headers

and in the ProTek Shield Adapter assembly shipped loose

in the accessory carton for field installation on brass ASME

headers).
This component provides protection to the heat exchanger

against galvanic corrosion, when properly bonded to the

heat exchanger. It should be replaced when the weight of

the ProTek Shield is reduced to about 40% of the original

weight (1.46 #).

F10715

Figure 19. ProTek Shield Assy

Polymer Headers (Residential Models)

Before attaching the 2-inch unions to the inlet/outlet

header, make sure the O-rings are properly seated in

the grooves. Use Aqualube or equivalent non-petroleum-

based lubricant on the O-ring.

Hand tighten the unions

Glue PVC piping directly to the unions.

F10641

O-RING

HEADER FLANGE

(CPVC)

HEADER FLANGE NUT

(CPVC)

PROTEK

SHIELD

ASSY

PLUMBING

Figure 17. Inlet/Outlet Header – Polymer

High temperature CPVC header flanges and header

flange nuts are provided. If there is any possibility of back-

siphoning when the pump stops, it is suggested that a

check valve (or valves) also be installed in the system.

6000.592A_PoolSpa_LoNOx.indd 15

11/22/2019 10:44:42 AM

Summary of Contents for Low NOx Series















































Search results

Summary of Contents for Low NOx Series

Reviews:

Related manuals for Low NOx Series

Brands by name

Popular brands

Raypak Low NOx Series, Installation And Operation Manual

Search results

Summary of Contents for Low NOx Series

Reviews:

Related manuals for Low NOx Series

Brands by name

Popular brands