Raymarine i60 ch wind Installation And Operation Instructions Manual Download Page 55

Page: 55 / 70

11.2 Instrument troubleshooting

Fault

Cause

Action

Blank display.

No power supply.

• Check fuse / circuit breaker.

• Check power supply.

• Check SeaTalk / SeaTalk

cabling

and connector security.

SeaTalk / SeaTalk

information not being

transferred between instruments.

SeaTalk / SeaTalk

cabling or connector

fault.

• Check security of SeaTalk / SeaTalk

connections between units.

• Check condition of SeaTalk / SeaTalk

cables.

• Isolate faulty unit by disconnecting

units one by one.

A group of SeaTalk / SeaTalk

units not

working.

SeaTalk / SeaTalk

cabling or connector

fault.

• Check the security of SeaTalk /

SeaTalk

connectors between

functioning and non-functioning units.

• Check the condition of SeaTalk /

SeaTalk

cable between functioning

and non-functioning units.

Troubleshooting

Summary of Contents for i60 ch wind







































































Search results

Summary of Contents for i60 ch wind

Reviews:

Related manuals for i60 ch wind

Brands by name

Popular brands

Raymarine i60 ch wind, Installation And Operation Instructions Manual

Search results

Summary of Contents for i60 ch wind

Reviews:

Related manuals for i60 ch wind

Brands by name

Popular brands