Raymarine E70058, Installation And Operation Instructions Manual, Page: 44 / 68

Note: The Maximum speed , Average speed and VMG pages
are temporary pages and will time-out after 8 seconds and revert
to the
Current speed page.
Using Tridata trip pages
To cycle through the trip, log, water temperature and timer pages
follow the steps below.
Trip
Trip
Trip
Trip
Trip
D12540-1
1. Press the Trip button to cycle through the Trip , Log , Water
temperature and Timer pages.
Setting the race start timer
The race start timers can be set from 1 to 15 minutes.
+
-
Re s e t
Re s e t
D12541-1
Time r
Time r
+
Re s e t Time r
+
1 2
With a race timer displayed
1. Press and hold the Timer and Reset buttons simultaneously to
enter adjust mode.
2. In adjust mode:
i. Use the Reset button to increment the race timer start value,
or
ii. Use the Timer button to decrease the race timer start value.
iii. Press and hold the Timer and Reset buttons simultaneously
to exit adjust mode.
Note: After a race start timer has counted down to zero it will
then start to count up.
Timer buzzer
The Timer buzzer is enabled or disabled during calibration see the
User calibration section.
When using a race timer with the timer buzzer enabled, the buzzer
will:
• Double beep every minute.
• Beep 3 times at the start of the last 30 seconds.
• Beep once for each of the last 10 seconds.
• Beep for 2 seconds at zero.
7.5 Group illumination
Group illumination is used to synchronizes and control the
backlighting level of multiple units assigned to the same group.
The unit can participate in shared illumination via a SeaTalk network
or group illumination via a SeaTalk
ng network.
When connected on a SeaTalk network all compatible units will
share their backlight level (when 1 unit's backlighting level is
adjusted all other units backlight level will also change).
When connected on a SeaTalk ng network the unit can participate in
group illumination and be assigned to a group of units which will
share their backlighting levels. Available groups are as follows:
• Helm 1
• Helm 2
• Cockpit
• Flybridge
• Mast
• grP1 to grP5
When assigned to a group, when the backlighting of 1 unit is
adjusted the backlighting level of all units assigned to the same
group will also change.
Assigning the i50 Depth to a group
To assign the i50 Depth as part of a group so that it can participate
in group illumination follow the steps below.
During normal operation:
1. Press and hold the Depth and Alarm buttons simultaneously
for 6 seconds.
The Group brightness entry page is displayed.
Note: The Group brightness entry page is a temporary page
and will time-out to the previous page after 8 seconds.
2. Press the Depth button to display the Group page.
3. Use the Offset or Reset buttons to select the group the unit
will be assigned to.
Assigning the i50 Speed to a group
To assign the i50 Speed as part of a group so that it can participate
in group illumination follow the steps below.
During normal operation:
1. Press and hold the Speed and Trip buttons simultaneously for
6 seconds.
The Group brightness entry page is displayed.
Note: The Group brightness entry page is a temporary page
and will time-out to the previous page after 8 seconds.
2. Press the Speed button to display the Group page.
3. Use the Timer or Reset buttons to select the group the unit will
be assigned to.
Assigning the i50 Tridata to a group
To assign the i50 Tridata as part of a group so that it can participate
in group illumination follow the steps below.
During normal operation:
1. Press and hold the Depth and Speed buttons simultaneously
for 6 seconds.
The Group brightness entry page is displayed.
Note: The Group brightness entry page is a temporary page
and will time-out to the previous page after 8 seconds.
2. Press the Depth button to display the Group page.
3. Use the Trip or Reset buttons to select the group the unit will
be assigned to.
44 i50