RG55R Operation • Service • Maintenance
16
Safety
Maintain control of the machine. Do not overload the machine
beyond the machine capacity.
Never straddle a wire cable. Never allow personnel to
straddle a wire cable.
Know the maximum dimensions of your machine.
Observe all applicable local government regulations when
you use this machine.
All personnel using this Machine must be trained in the
operation, safety and maintenance repair procedures.
Careless use of this Equipment could result in serious injury
or even death.
ALL PROCEDURES IN THE SAFETY AND OPERATION
SECTIONS OF THIS MANUAL MUST BE READ AND
UNDERSTOOD BEFORE STARTING THIS MACHINE.
• All operators must be wearing the proper Personal
Protective Equipment before attempting to start and
operate this machine.
• Do not allow children or other spectators to standby
and watch the machine in operation.
• Familiarize yourself with all of the controls in a safe
environment before starting to work with this machine.
• Always have more than one person at the job site. If an
accident occurs, someone is there to assist or obtain help.
• Never operate or allow someone to operate the machine
while under the influence of alcohol, drugs, or any
medication that could affect the operator’s performance
and concentration. Maintain a drug-free work place.
• Always operate this machine with all safety equipment in
place and working. Make sure all controls are properly
adjusted for safe operation.
• Do not change the engine governor settings or over
speed the engine. The governor controls the maximum
safe operating speed of the engine
• Never leave this machine unattended with the engine
running.
• Use only your hand to operate the controls. Never use
a foot, knee, rope or any extension device.
• Never hand-feed this machine for any reason.
• Contact with moving parts, belts or rotating cutter wheels
can kill, injure or dismember.
• Turn off engine and wait for all movement to stop before
working on this machine. Lock-out/Tag Out all controls.
• If equipped, the Emergency Stop buttons must be
operating properly. These should each be checked and
verified to shut down the engine by the operator prior
to performing any work.
• CAUTION! FLYING DEBRIS!
NEVER stand or allow
anyone else to be directly in front of machine.
• Material being discharged from machine can cause
severe injury, blindness or death.
• Always operate this machine from the operator area.
Never stand directly in front of machine as flying objects
could be thrown during operation.
• Never move this machine, or make adjustments or repairs,
while the engine is running.
Slope Operation
Machines that are operating safely in various applications
depend on these criteria: the machine model, configuration,
machine maintenance, operating speed of the machine,
conditions of the terrain, fluid levels, and tire inflation
pressures. The most important criteria are the skill and
judgment of the operator.
A well trained operator that follows the instructions in the
Operation and Maintenance Manual has the greatest impact
on stability. Operator training provides a person with the
following abilities: observation of working and environmental
conditions, feel for the machine, identification
of potential hazards, and operating the machine safely by
making appropriate decisions.
When you work on side hills and when you work on slopes,
consider the following important points:
• Speed of travel – At higher speeds, forces of inertia
tend to make the machine less stable.
• Roughness of terrain or surface – The machine may be
less stable with uneven terrain.
• Direction of travel – Avoid operation the machine across
the slope. When possible, operate the machine up
the slopes and operate the machine down the slopes.
• Place the heaviest end of the machine uphill when you
are working on an incline.
• Mounted equipment – Balance of the machine may be
impeded by the following components: equipment that
is mounted on the machine, machine configuration,
weights, and counterweights.
• Nature of surface – Ground that has been newly filled
with earth may collapse from the weight of the machine.
• Surface material – Rocks and moisture of the surface
material may drastically affect the machine’s traction and
machine’s stability. Rocky surfaces may promote side
slipping of the machine.
• Slippage due to excessive loads – This may cause
downhill tracks or downhill tires to dig into the ground,
which will increase the angle of the machine.
• Width of tracks or tires – Narrower tracks or narrower
tires further increase the digging into the ground which
causes the machine to be less stable.
• Implements attached to the machine hitch or drawbar
– This may decrease the weight on the uphill tracks.
This may also decrease the weight on the uphill tires.
The decreased weight will cause the machine to be
less stable.
• Height of machine working load. When the working loads
are in higher positions, machine stability is reduced.
• Operated equipment – Be aware of performance
Summary of Contents for RG55R
Page 27: ...RG55R Operation Service Maintenance 800 392 2686 27 Operation...
Page 58: ...RG55R Operation Service Maintenance 58 Hydraulic Schematic 805921...
Page 59: ...RG55R Operation Service Maintenance 800 392 2686 59 Hydraulic Schematic 805921...
Page 67: ...RG55R Operation Service Maintenance 800 392 2686 67 Specifications...
