Raven SmarTrax Installation Manual Download Page 8 | Manualshive

Page: 8 / 59

background image

Chapter 2

4

John Deere 7X00/7X10 Series SmarTrax™ Installation Manual

Preparing for Installation

Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the
machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic
system by loosening the hydraulic fittings slowly, where applicable.

During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.

Recommendations

Raven Industries recommends the following best practices when installing or operating the SmarTrax system
for the first time, at the start of the season, or when moving the SmarTrax system to another machine:

•

Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the
machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic
hoses, etc.).

•

Ensure the machine’s hydraulic valve is using fresh oil and debris is flushed from the hydraulic hoses,
valves, and filters.

Raven Industries recommends the following best practices when installing the SmarTrax system:

•

Use part numbers to identify the parts.

•

Do not remove the plastic wrap from a part until it is necessary for installation.

•

Do not remove plastic caps from a part until it is necessary for installation.

Point of Reference

The instructions in this manual assume that you are standing behind the machine, looking toward the cab.

Kit Contents

This section contains a list of the components that are included in the SmarTrax kit. Before beginning the
SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about
the kit, contact your Raven dealer.

TABLE 1.

John Deere 7X00/7X10 MFWD SmarTrax Installation Kit (P/N 117-5034-004)

Picture

Item Description

Part Number

Qty.

Not Pictured

Manual - John Deere 7X00 and 7X10 Series
SmarTrax Installation Manual

016-5034-004

1

Valve - SmarTrax Hydraulic

334-0003-088

1

«
...
6
7
8
9
10
...
»

Summary of Contents for SmarTrax




























































Reviews:

No comments

Related manuals for SmarTrax

Brand: Samson Pages: 20

Univerge SV9100

Brand: NEC Pages: 478

Univerge UM8000

Brand: NEC Pages: 46

Brand: NEC Pages: 149

Brand: NEC Pages: 13

Brand: VCON Pages: 66

EtherNetIP ControlPlex CPC12EN

Brand: E-T-A Pages: 28

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

PDS CONTROL Series

Brand: S&P Pages: 32

Brand: Burlington Pages: 7

Brand: Gain Electronic Pages: 17

Brand: Vexve Pages: 24

Brand: H3C Pages: 15

Brand: Polycom Pages: 10

Brand: Quick Pages: 16

Brand: Danfoss Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands