Raven SmarTrax Installation Manual Download Page 46 | Manualshive

Page: 46 / 59

background image

Chapter 5

42

John Deere 7X00/7X10 Series SmarTrax™ Installation Manual

•

Securely fasten the node using bolts or screws through at least two of the three mounting holes. When
mounted properly, the node should not become loose or rotate.

Install the Foot Switch

FIGURE 6.

Foot Switch Installed

1.

Select a suitable location for the foot switch (P/N 063-0172-470) to be installed.

Note:

The foot switch should be installed in a location where the operator has easy access to it and is
able to fully press the pedal.

2.

Using the holes in the foot switch as a template, drill holes in the floor of the cab.

3.

Secure the foot switch to the floor by installing the supplied screws in each of the mounting holes.

Install the Node Harness

FIGURE 7.

Node Harness Installed

«
...
44
45
46
47
48
...
»

Summary of Contents for SmarTrax




























































Reviews:

No comments

Related manuals for SmarTrax

HomeTec Pro CFF3000

Brand: Abus Pages: 13

Brand: NAVITAS Pages: 7

Brand: Abus Pages: 2

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Jabra Pages: 18

Brand: Samson Pages: 20

Brand: NAPCO Pages: 48

Magnum Alert 2600

Brand: NAPCO Pages: 68

Brand: Pando Pages: 43

Brand: Rane Pages: 2

Compact Comfort VAV12

Brand: SAI HVAC Pages: 16

Brand: saia-burgess Pages: 203

Brand: Sailor Pages: 1

Brand: Samson Pages: 8

Brand: Samson Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands