Raven SmarTrax Installation Manual Download Page 36 | Manualshive

Page: 36 / 59

background image

Chapter 4

32

John Deere 7X00/7X10 Series SmarTrax™ Installation Manual

FIGURE 14.

Sensor Centering Bracket Installed

4.

Slide the sensor centering bracket tight against the kingpin bolt as shown in Figure 14 above.

Note:

The bracket should be positioned so that the slot is in line with the front axle.

5.

Fully tighten the kingpin bolt, ensuring the bracket stays aligned with the axle and tight against the kingpin
bolt.

FIGURE 15.

WAS Coupler Installed

6.

Install the WAS coupler (P/N 307-0159-419) in the rectangular cutout of the sensor centering bracket.

Note:

The flat side of the ‘D’ profile should be closest to the machine’s engine.

FIGURE 16.

Rotary Sensor Installed on Sensor Bracket

Flat Face of ‘D’
Profile

Sensor
Connector

Bracket
Base

«
...
34
35
36
37
38
...
»

Summary of Contents for SmarTrax




























































Reviews:

No comments

Related manuals for SmarTrax

Brand: VCON Pages: 66

EtherNetIP ControlPlex CPC12EN

Brand: E-T-A Pages: 28

Brand: Samson Pages: 52

Brand: janitza Pages: 58

Brand: Mackie Pages: 4

Brand: Parker Pages: 30

Compax3M Series

Brand: Parker Pages: 52

Brand: Parker Pages: 337

Brand: YUGE Pages: 69

Brand: Quectel Pages: 232

Brand: Quectel Pages: 9

Brand: Quectel Pages: 73

Brand: Grundfos Pages: 16

Brand: Loewe Pages: 62

Brand: Shimaden Pages: 32

Brand: LAB-EL Pages: 25

Brand: Cardigo Pages: 12

Brand: MERCATOR Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands