background image

While every effort has been made to ensure the accuracy of this document, 
Raven Industries assumes no responsibility for omissions and errors. Nor is any 
liability assumed for damages resulting from the use of information contained 
herein.

Raven Industries shall not be responsible or liable for incidental or consequential 
damages or a loss of anticipated benefits or profits, work stoppage or loss, or 
impairment of data arising out of the use, or inability to use, this system or any of 
its components. Raven Industries shall not be held responsible for any 
modifications or repairs made outside our facilities, nor damages resulting from 
inadequate maintenance of this system.

As with all wireless and satellite signals, several factors may affect the availability 
and accuracy of wireless and satellite navigation and correction services (e.g. 
GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the 
accuracy, integrity, continuity, or availability of these services and cannot 
guarantee the ability to use Raven systems, or products used as components of 
systems, which rely upon the reception of these signals or availability of these 
services. Raven Industries accepts no responsibility for the use of any of these 
signals or services for other than the stated purpose.

Disclaimer

©Raven Industries, Inc. 2012

Summary of Contents for SmarTrax Case IH Steiger 335





































Reviews: