background image

5

2.

MOUNTING THE FLOW METER

l)

Mount the Flow Meter in the area of the boom valves per Figure 4.  All flow through

the Flow Meter must go to booms only, i.e. no return line to tank or pump after

Flow Meter.

2)

Mount Flow Meter horizontal to the ground.  Use the bracket to secure the Flow

Meter.

3)

For best results, allow a minimum of 7 1/2 inches [20 cm] of straight hose on inlet

of Flow Meter.  Bend radius of hose on outlet of Flow Meter should be gradual.

4)

Flow must be in direction of arrow on Flow Meter.

NOTE:

For flow rates less than 3 GPM [11 lit/min], mount the Flow Meter

vertically with arrow pointing upward.  (Refer to Appendix 3 for

alternate plumbing diagram).

NOTE:

It is essential, when using suspensions, that the system be thoroughly

rinsed out each day after use.  Failure to do so may cause system to

malfunction.

3.

MOUNTING THE CONTROL VALVE

l)

Mount the motorized Control Valve in the main hose line between the Flow Meter

and the booms, with motor in the upright position.  (For less than 3 GPM [11 lit/

min] the motorized Control Valve is mounted in the by-pass line, refer to Appendix

3 for alternate plumbing diagram).

2)

Connect the Flow Control Cable connectors to boom valves, Flow Meter, and motorized

Control Valve.  (Black wire to boom valve #1, Brown wire to boom valve #2, and

Blue wire to boom valve #3, Black/White wire to boom Valve #4).

FIGURE 4

Summary of Contents for SCS 340






































Reviews: