Raven AutoBoom Installation Manual Download Page 73

Page: 73 / 92

Manual No. 016-0230-004 Rev. F

UltraGlide

Mount the sensor bracket to the front-right side of the machine’s center rack using two 3/8”-16 UNC x 1” hex
bolts (P/N 311-0054-105) and two 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164) as shown in Figure 11
above.

Tighten the nut to ensure the sensor is mounted securely.

Connect the Sensor Cables

Connect the left sensor cable (P/N 115-0171-527) to the connector on the left sensor.

Route the left sensor cable toward the AutoBoom valve.

Loop and tie-off any excess cable, allowing enough cable for boom folding and extension.

Repeat the steps above to connect the remaining sensor cable(s).

Note:

The sensor cables will be connected to the AutoBoom system in the wiring phase of installation.

Summary of Contents for AutoBoom




























































































Search results

Summary of Contents for AutoBoom

Reviews:

Related manuals for AutoBoom

Brands by name

Popular brands

Raven AutoBoom, Installation Manual

Search results

Summary of Contents for AutoBoom

Reviews:

Related manuals for AutoBoom

Brands by name

Popular brands