Raven AutoBoom Installation Manual Download Page 77

Page: 77 / 92

Manual No. 016-0230-004 Rev. F

UltraGlide

FIGURE 16.

AutoBoom Harness Cable Connections Diagram

21.

Cut the smaller male LEFT SOLENOID UP SENSE connector off the yellow wire on the AutoBoom harness
cable (P/N 115-0230-052).

22.

Plug the removed connector into the remaining female LEFT SOLENOID UP SENSE connector on the
AutoBoom harness cable.

23.

Strip the insulation back from the cut ends of the installed boom sense adapter cable (P/N 115-0171-559)
and the AutoBoom harness cable.

24.

Splice the bare ends of the cables together using butt splices (not provided) and wrap them with electrical
tape.

25.

Cut the smaller male LEFT SOLENOID DOWN SENSE connector off the black wire on the AutoBoom
harness cable.

26.

Plug the removed connector into the remaining LEFT SOLENOID DOWN SENSE connector on the
AutoBoom harness cable.

27.

Strip the insulation back from the cut ends of the installed boom sense adapter cable and the AutoBoom
harness cable.

28.

Splice the bare ends of the cables together using butt splices (not provided) and wrap them with electrical
tape.

29.

Cut the smaller male RIGHT SOLENOID UP SENSE connector off the wire on the AutoBoom harness
cable.

30.

Plug the removed connector into the remaining RIGHT SOLENOID UP SENSE connector on the AutoBoom
harness cable.

31.

Strip the insulation back from the cut ends of the installed boom sense adapter cable and the AutoBoom
harness cable.

32.

Splice the bare ends of the cables together using butt splices (not provided) and wrap them with electrical
tape.

33.

Cut the smaller male RIGHT SOLENOID DOWN SENSE connector off the wire on the AutoBoom harness
cable.

34.

Plug the removed connector into the remaining RIGHT SOLENOID DOWN SENSE connector on the
AutoBoom harness cable.

35.

Strip the insulation back from the cut ends of the installed boom sense adapter cable and the AutoBoom
harness cable.

36.

Splice the bare ends of the cables together using butt splices (not provided) and wrap them with electrical
tape.

Cut Here

Summary of Contents for AutoBoom




























































































Search results

Summary of Contents for AutoBoom

Reviews:

Related manuals for AutoBoom

Brands by name

Popular brands

Raven AutoBoom, Installation Manual

Search results

Summary of Contents for AutoBoom

Reviews:

Related manuals for AutoBoom

Brands by name

Popular brands