Raven AutoBoom Installation Manual Download Page 23

Page: 23 / 92

Manual No. 016-0230-004 Rev. F

PowerGlide

FIGURE 7.

Left and Right Cylinder Hoses Connected to the AutoBoom Valve

Connect the 90° end of the installed hydraulic hose to the fittings installed in Port LC of the AutoBoom
valve.

Disconnect the machine’s hose from the right tilt cylinder.

Install a 13/16” ORFS M/M/F swivel run tee adapter fitting (P/N 333-0012-028) on the right tilt cylinder.

Reinstall the machine’s hose on the opposite end of the installed tee fitting.

10.

Install a 13/16” ORFS M/F 90° swivel elbow fitting (P/N 333-0012-067) on the 90° end of the installed tee
fitting.

11.

Install the 90° end of the supplied hydraulic hose (P/N 214-1000-300) on the 90° end of the installed tee
fitting.

12.

Connect the straight end of the installed hydraulic hose to Port RC of the AutoBoom valve.

Summary of Contents for AutoBoom




























































































Search results

Summary of Contents for AutoBoom

Reviews:

Related manuals for AutoBoom

Brands by name

Popular brands

Raven AutoBoom, Installation Manual

Search results

Summary of Contents for AutoBoom

Reviews:

Related manuals for AutoBoom

Brands by name

Popular brands