manualshive.com logo in svg

Raven AutoBoom, Installation Manual

Introducing Raven AutoBoom - a cutting-edge agricultural technology. Achieve precision boom control with our state-of-the-art system. Unlock unparalleled efficiency, accuracy, and ease of use with our intuitive Calibration & Operation Manual. Download it for free on manualshive.com and unleash the full potential of your farming operations.

Share
Download
background image

Chapter 4

32

Miller Nitro 2000 Series AutoBoom™ Installation Manual

Important:

Tip the AutoBoom valve on its side and use the Allen wrench to remove the orifice from the cavity, 

taking care not to let the fitting fall into the valve. 

FIGURE 6.

Port Plug Reinstalled on the AutoBoom Valve

5.

Use the Allen wrench to reinstall the port plugs on Ports 3A and 3B of the AutoBoom valve.

FIGURE 7.

Coil Reinstalled on the AutoBoom Valve

6.

Reinstall the coils on the solenoids of the AutoBoom valve.

Install Fittings on the AutoBoom Valve

Before mounting the AutoBoom valve (P/N 063-0131-124) on the machine, install the proper fittings on the 
valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure. 
Refer to the following table to install the fittings in the appropriate ports of the AutoBoom valve.

Fitting

Part Number

Port

Fitting - 11/16” ORFS (M) to 9/16” SAE O-Ring (M) Straight Adapter

333-0012-084

LC, RC

Fitting - 13/16” ORFS (M) to 3/4” SAE O-Ring (M) Straight Adapter

333-0012-168

P, T

Fitting - 11/16” Hex 9/16” SAE O-Ring Plug

333-0012-194

LV, RV

Summary of Contents for AutoBoom





























































































Reviews:

No comments

Related manuals for AutoBoom

J4C 20 Mounting Instructions preview
20
Brand: J4C Pages: 4
ABB ACH550 series Quick Start Manual preview
ACH550 series
Brand: ABB Pages: 6
FrSky Taranis Q X7S Manual preview
Taranis Q X7S
Brand: FrSky Pages: 2
Aastra Ascotel Office 45 Operating Instructions Manual preview
Ascotel Office 45
Brand: Aastra Pages: 40
Aastra OpenCom 100 Mounting And Commissioning User Manual preview
OpenCom 100
Brand: Aastra Pages: 244
Aastra 632d Quick User Manual preview
632d
Brand: Aastra Pages: 30
Aastra 5380 Quick User Manual preview
5380
Brand: Aastra Pages: 24
Aastra IntelliGate A150 System Manual preview
IntelliGate A150
Brand: Aastra Pages: 524
Aastra Ascotel IntelliGate 150 System Manual preview
Ascotel IntelliGate 150
Brand: Aastra Pages: 228
Daikin Madoka User Manual preview
Madoka
Brand: Daikin Pages: 2
Daikin BRC7E530W8 Operation Manual preview
BRC7E530W8
Brand: Daikin Pages: 12
Daikin BRC1H81K Installation And Operation Manual preview
BRC1H81K
Brand: Daikin Pages: 12
Daikin BRC1H71W Operation Manual preview
BRC1H71W
Brand: Daikin Pages: 46
Daikin BRC1D71 Operation Manual preview
BRC1D71
Brand: Daikin Pages: 21
Daikin BRC1D517 Operation Manual preview
BRC1D517
Brand: Daikin Pages: 20
Harsco Industrial ENVI Advanced User'S Manual preview
ENVI
Brand: Harsco Industrial Pages: 57
Harmar Mobility AL600 Pioneer Installation And Owner'S Manual preview
AL600 Pioneer
Brand: Harmar Mobility Pages: 53
Jabra LINK 280 - User Manual preview
LINK 280 -
Brand: Jabra Pages: 8

Brands by name

Popular brands

Load more brands