Ravas SAFECHECK Installation And User Manual Download Page 32

Page: 32 / 33

USER MANUAL

– Safecheck

Heftruck

Indicator

3,15 A

Stekker accu truck

Optioneel

Elektrische truck

Filter

Omvormer

+12 V

Black

Red

Blue

Brown

omvormer

filter

Stekker

Zekering

3,15 A

Accu

elektrische vorkheftruck

Indicator

11.1.3 Connection to electric forklifts

Connect the power supply to the battery as close as possible to, but not directly on, the battery and

not in front of a main breaker.

Connect the red wire (indirectly: with plug in between) with the positive energy source (plus pole of the

battery) of the forklift.

Connect the black wire (indirectly: with plug in between) to the negative power source (negative pole

of the battery) of the lift truck.

Make sure the wire connectors are sufficiently isolated from each other.

Connect the battery back on the fork-lift truck

Electrical forklift

plug

Battery electrical forklift

converter

Forklift

truck

converter

Plug battery truck

Optional

Summary of Contents for SAFECHECK


































Search results

Summary of Contents for SAFECHECK

Reviews:

Related manuals for SAFECHECK

Brands by name

Popular brands

Ravas SAFECHECK, Installation And User Manual

Search results

Summary of Contents for SAFECHECK

Reviews:

Related manuals for SAFECHECK

Brands by name

Popular brands