background image

Stand 25.05.2011 

Seite 19

Operating instruction TAXON

Page 19

 of 42

3.6 

Disassembly of the serial parking legs and the wood transportation pallet

After attaching, lift the spreader lightly with the three-point attachment of the tractor.

Then pull out the delivered wood pallet from under the spreader.

Never reach under the lifted spreader!

The spreader is delivered ex work with a series parking system
(two parking legs, 1) taking the weight of the unloaded spreader.

The parking legs cannot be adjusted in height.
A locking bolt is fi tted to the parking leg (2). This fi xes the parking leg to
the guide block of the attachment horse.

Keep hold of the parking leg with one hand, pull the locking bolt with the
other hand and take the parking leg downward.

• 

The spreader must be placed unloaded on the parking legs delivered ex works only!
Pay attention to the carrying load of the parking legs!

• 

Never step under the parked spreader!

• 

Place the spreader only on solid and even ground!

• 

Store parking legs only lying! 

Danger of falling over!

• 

Unauthorised alterations to the parking legs are prohibited!

• 

Never step or reach under the lifted spreader!

Safety distance: 
Minimum 200 mm

1)

2)

Summary of Contents for TAXON 25.1











































Reviews: