background image

Communication

Page 4

Landline:

To connect your analog phone line to the Tower:

1. 

Open Access Panel 1 (see Figure 1) using the torx bit to remove the security screws.

2. 

Locate the gray phone cable coming out of the NEMA 4 box.

3. 

Connect the gray phone cable to the phone cable that was run through the conduit either by connecting the  

    modular jack or the red and green wires.

 

Items Needed for Installation

• Concrete for 16” deep, 2’ diameter

• RATH®

 

Kit 7476* or 7477** 

• #1 Phillips screwdriver

• 1/4” driver

• Torx bit (provided to remove access panels)

*7476 (For New Concrete)

 • (4) 3/4” x 12” galvanized anchor bolts

 • (12) 3/4” flat washers

 • (4) 3/4” hex nuts
 • (4) 3/4” SAE washers
 • (4) split lock washers

**7477 (For Existing Concrete)

   • (4) anchors
   • (4) 3/4” x 4” galvanized anchor bolts
   • (1) setting tool

   • (8) 3/4” flat washers

   • (4) split lock washers 

• 1/4” spanner adapter (provided to remove access panels)

• Adjustable wrench

• Analog phone line (if using 900 MHz or a Landline)

• Phone cable (if using 900 MHz or a Landline)

Tower Installation

1.

 Lay Tower on its side with the base next to the concrete pad.

2.

 Open lower Access Panel 2 on back of Tower (see Figure 1).

3.

 Feed the electrical and phone wires in the conduit into the Tower base through the 4” hole.

4.

 Align the Tower mounting holes with the four 3/4” galvanized rods and lift on to the concrete slab.

5.

 Put a lock washer on each rod along with a nut and secure tightly.

Connecting the Electric Lines:

1.

 Locate the black (positive) and white (negative) wires that exit the NEMA 4 box behind the face plate.

    (see Figure 1).

2.

 Connect the electrical wires from the conduit to the wires in the Tower using the waterproof wire 

    nuts located on the wires.

Connecting the Phone and Turning On the Electric Power:

1.

 Locate the gray phone cable coming out of the NEMA 4 box behind the face plate.

2.

 If using an analog phone line for communication, connect tip and ring from phone line run through conduit to  

    red and green phone cable coming out of the NEMA 4 box.

Note:

 If using Cellular or 900 MHz, phone line should already be connected within the Tower.

3.

 Turn on the electrical power.

Summary of Contents for 2100-TL9










Reviews: